What did you do to your SC today?
12-05-17, 12:46 PM
#7021
Yeah, it sucks. The part that pissed me off was that it happened after i cleaned the garage and scrubbed all the atf off of the ground. I would have been less mad if it leaked right when I installed the rack because it would be easier to pull off. I'm going to try and pull the rack tonight, so I can swap the EVO sensor back to the old rack and drop it off at the rebuild shop in the morning.
12-06-17, 09:01 AM
#7022
Yeah, it sucks. The part that pissed me off was that it happened after i cleaned the garage and scrubbed all the atf off of the ground. I would have been less mad if it leaked right when I installed the rack because it would be easier to pull off. I'm going to try and pull the rack tonight, so I can swap the EVO sensor back to the old rack and drop it off at the rebuild shop in the morning.
Did you have to put on new steering rack bushings with your rack or did they come with the rack?
12-07-17, 12:44 AM
#7027
Driver School Candidate
Kira X, the Figs bushings can be found at www.shopfigs.com , they have a bunch of suspension components.
12-07-17, 04:26 AM
#7028
12-07-17, 08:47 AM
#7030
Thanks! Now if he would only make pods for the center vents... 
EDIT: Just spoke to AutoExtrude about a possible center vent pod and its basically not in the works because the vent is 51mm tall and the pods are 52mm... Ah well!
EDIT: Just spoke to AutoExtrude about a possible center vent pod and its basically not in the works because the vent is 51mm tall and the pods are 52mm... Ah well!
Last edited by mrmj2u; 12-07-17 at 08:51 AM.
12-07-17, 10:24 AM
#7031
It looks like someone else already answered where to buy them, but here is a direct link: http://www.shopfigs.com/v3/by-vehicl...C3_SUP_RCKBUSH I'm a big fan of Figs engineering products. Their products are well constructed and more thought out than some of their competitors that I've experienced. Tolerances and ease of adjust-ability are factored into their design.
The solid steering rack bushings only replaces the bushings on the driver side, so the passenger side still uses the oem rubber.
I picked up my rack yesterday and they cleaned everything way better than I could.
I was asking them about the rack I put in, and they said for it to fail that fast would require me to over pressure the system which is usually done when people swap the high and low pressure lines. He said it was unlikely I did that since the high and low lines use different sized bolts. It's more likely the rack was defective when I got it.
While swapping everything over and getting ready to install the newer rebuilt rack, I noticed the pinch bolt on the steering shaft was stretched out. I ordered them last night, so now it's just more waiting.
The solid steering rack bushings only replaces the bushings on the driver side, so the passenger side still uses the oem rubber.
I picked up my rack yesterday and they cleaned everything way better than I could.
I was asking them about the rack I put in, and they said for it to fail that fast would require me to over pressure the system which is usually done when people swap the high and low pressure lines. He said it was unlikely I did that since the high and low lines use different sized bolts. It's more likely the rack was defective when I got it.
While swapping everything over and getting ready to install the newer rebuilt rack, I noticed the pinch bolt on the steering shaft was stretched out. I ordered them last night, so now it's just more waiting.
12-07-17, 06:39 PM
#7032
Not today, but yesterday I bought, cleaned and painted ls400 bbk with purple luscious metal cast duplicolor rattle tat tat tat and, waiting on the my hoes to come in 
rockauto sent me the tie rod ends can someone besides me confirm that these are wrong?
now pic time
rockauto sent me the tie rod ends can someone besides me confirm that these are wrong?
now pic time
12-07-17, 07:22 PM
#7033
It looks like someone else already answered where to buy them, but here is a direct link: http://www.shopfigs.com/v3/by-vehicl...C3_SUP_RCKBUSH I'm a big fan of Figs engineering products. Their products are well constructed and more thought out than some of their competitors that I've experienced. Tolerances and ease of adjust-ability are factored into their design.
The solid steering rack bushings only replaces the bushings on the driver side, so the passenger side still uses the oem rubber.
I picked up my rack yesterday and they cleaned everything way better than I could.
I was asking them about the rack I put in, and they said for it to fail that fast would require me to over pressure the system which is usually done when people swap the high and low pressure lines. He said it was unlikely I did that since the high and low lines use different sized bolts. It's more likely the rack was defective when I got it.
While swapping everything over and getting ready to install the newer rebuilt rack, I noticed the pinch bolt on the steering shaft was stretched out. I ordered them last night, so now it's just more waiting.
The solid steering rack bushings only replaces the bushings on the driver side, so the passenger side still uses the oem rubber.
I picked up my rack yesterday and they cleaned everything way better than I could.
I was asking them about the rack I put in, and they said for it to fail that fast would require me to over pressure the system which is usually done when people swap the high and low pressure lines. He said it was unlikely I did that since the high and low lines use different sized bolts. It's more likely the rack was defective when I got it.
While swapping everything over and getting ready to install the newer rebuilt rack, I noticed the pinch bolt on the steering shaft was stretched out. I ordered them last night, so now it's just more waiting.
Did the rack come with the new tie rod ends or did you have to buy those separately?
Ill be replacing mine wih the fresher unit because cracked the front bushing loop ftl
ordered new rods tbuy I think they are wrong or at least one of them is.
Tthe new rack looks great and will feel much better!! And new figs bushings will make a tighter steering and a little more precise as well!!! Figs here too along with the battles!!
Thank you!!
12-07-17, 07:58 PM
#7034
Did the rack come with the new tie rod ends or did you have to buy those separately?
Ill be replacing mine wih the fresher unit because cracked the front bushing loop ftl ordered new rods t
buy I think they are wrong or at least one of them is.
Tthe new rack looks great and will feel much better!! And new figs bushings will make a tighter steering and a little more precise as well!!! Figs here too along with the battles!!
Thank you!!
Ill be replacing mine wih the fresher unit because cracked the front bushing loop ftl
ordered new rods tbuy I think they are wrong or at least one of them is.
Tthe new rack looks great and will feel much better!! And new figs bushings will make a tighter steering and a little more precise as well!!! Figs here too along with the battles!!
Thank you!!
The following users liked this post:
LEXXIUM (04-17-18)
12-08-17, 01:37 AM
#7035
Driver School Candidate
Added new water pump and timing belt and painted hooks red...
Some more things accomplished. Changed the transmission fluid, replaced spark plug x8, oil filter, engine flush with oil change, fuel injector cleaning, and painted ls400 brake upgrade red.
Some more things accomplished. Changed the transmission fluid, replaced spark plug x8, oil filter, engine flush with oil change, fuel injector cleaning, and painted ls400 brake upgrade red.
Last edited by Mikeezi; 12-08-17 at 06:57 AM.