ClubLexus - Lexus Forum Discussion

ClubLexus - Lexus Forum Discussion (https://www.clublexus.com/forums/)
-   SC - 1st Gen (1992-2000) (https://www.clublexus.com/forums/sc-1st-gen-1992-2000-6/)
-   -   Dyno'd my 2JZ-GTE swapped SC. (https://www.clublexus.com/forums/sc-1st-gen-1992-2000/316766-dynod-my-2jz-gte-swapped-sc.html)

TTSC3 Nov 5, 2007 09:37 PM

Dyno'd my 2JZ-GTE swapped SC.
 
I just tuned my 2JZ-GTE swapped SC a few days ago on the dynojet. 371whp was what I got. As I was tuning, people were telling me that my numbers were more than most people make, but I didn't really have much to compare it with. All I have is a full exhaust (3in downpipe, and a Y pipe that goes down to 2.5in out each side), no cats, HKS FMIC, stock twins, no boost controller or BCC either. I was gonna turn the boost up, but I figured since I have like another 10k in parts to install, which includes a single kit, what's the point? It was just to see where I was at and to make sure the tune was safe after the FMIC install. Where is everone experiencing boost cut at? I haven't hit it yet, and don't have my boost gauge hooked up yet, but I was told that boost cut on a supra is at a pretty modest boost level. I'll post the dyno plot up tomorrow or the day after, as I won't be at the shop for a day or 2, but do these numbers seem like they're correct? Thanks.

LCSC Nov 6, 2007 12:02 AM

Sweet:thumbup:

xspsi6 Nov 6, 2007 12:13 AM

jdm or usdm?

Dx3 Nov 6, 2007 05:43 AM

What engine management are you going to use?

Jonny

TTSC3 Nov 6, 2007 06:34 AM


Originally Posted by Dx3 (Post 3036815)
What engine management are you going to use?

Jonny

AEM. It has an SAFC in it right now, but I really only use AEM's on cars I tune. I already have the AEM, I'm just waiting for PTE to send the turbo to the shop, so I can throw that on along with the AEM.

TTSC3 Nov 6, 2007 06:35 AM


Originally Posted by xspsi6 (Post 3036676)
jdm or usdm?

JDM motor.

plex Nov 6, 2007 06:38 AM

Nice bpu numbers I will be doing a usdm swap pretty soon will stay on stock twins until I really figure out what I want. What size single are you going with?

Blizzy Nov 6, 2007 06:54 AM


Originally Posted by cherplex (Post 3036889)
What size single are you going with?

I would love to hear this as well.

I recall reading on Supraforums that stock boost cut is 1 bar. Don't hold me to that, however, since I have no direct experience with the 2JZ.

TTSC3 Nov 6, 2007 07:16 AM

Probably a 4088R, but I've been toying with a few ideas. 550whp on pump gas is what I want out of it, but with good response, so I'll pretty much narrow it down based on that.

hemogoblin Nov 6, 2007 07:17 AM

What psi and octane was this at?

TTSC3 Nov 6, 2007 07:21 AM


Originally Posted by hemogoblin (Post 3036962)
What psi and octane was this at?

Stock boost and pump gas. No BCC, so boost couldn't have been more than 13-14psi.

RX7 RAGE Nov 6, 2007 06:59 PM

nice, can't wait to get my gte swapped sc running. :)

daSC4 Nov 6, 2007 08:03 PM

very nice numbers for a bpu 2jz

WoRKeDiT Nov 6, 2007 08:30 PM

nice numbers, im working on my gte swap in my sc as well. hope my numbers are as good

ISC400 Nov 7, 2007 06:23 AM

can't wait see your number after you go single and AEM:thumbup:


All times are GMT -7. The time now is 09:10 PM.


© 2026 MH Sub I, LLC dba Internet Brands