JesLet

iTrader: (19)

Damn 50mm almost 2 inch... It's ready for 345s

benjiSC3

XXR 531 black Chromium

F: 18x8.5 +20
245/45/18

R: 18x9.5 +20
245/40/18

Currently not rolled but planning to. Not planning to pull
Fronts rub under compression and full lock
Rears rub over large bumps, ie train tracks

myLEXsc400

Wheels look good, but the profile on the front is way too big. I would recommend a 235/40/18
Now all it needs is some more low

JasGS350

iTrader: (7)

Not going to work unless you pull. I have a 10.5 +22 in the rear on mine as well, with 245x30's and I have my rears rolled flat with no pull. No rubbing at all (Stance GR+ Pro Coilovers help ). BTW, I have 19" rims. Any bigger of a tire and I would need to raise my car or give it some neg camber. My 2 cents. Not the best pics.

nich1234

New to the forum, I drive a 95 sc400. I have bought kyb struts still in the box. And my espelir springs should be here in a couple of days. Im wanting to buy 18" fr500 wheels soon. And I was wondering what offset would be good for front and rear. I have access to a fender roller and will fold in the inside lip front and rear. Any advice is helpful. thanks

jadu

iTrader: (42)

18x10+22 all around would probably be the best sizes, at least from what I looked up. Since you have access to a fender roller, I would roll all four corners flat because depending on the tire sizes you wanna run, you'll need it. The espelirs give a pretty good drop

nich1234

I was thinking 9's up front because I don't want too much poke and as little camper as possible.

malikb

does anyon know approximently how much it would cost to re-rap in chrome 19" deep dish rims

DoYuEvenSc

iTrader: (1)

Hey everyone I would like to ask if anyone could help me out I have a set of 18x9.5 wheels with a +25 offset my set up is still a little sunk in I am planning on getting spacers but am puzzled what size to get I was thinking either a 10mm or a 15mm since I'm trying to get a flush/stance look to my sc but would like to get some expert advice on it
Thanks

bigwes

I say get 225/40 in the front and 235/40 or 225/40 or 235/35 in the rear. Then give it a nice drop and ur all good

JesLet

iTrader: (19)

This is 295/30/18 on Eibach/Tokico, as you can see there's big gap. I was thinking about getting another set of 295/45, do you guys think it will fill the gap or just going to be the same but with fatter side wall? I'm into meaty tires

Don't mind the chipping paint... intended to get a paint job anyway haha

SC300T1

iTrader: (1)

Looking at picking up some 2010 mustang rims for my stock 92 sc300. Would these bolt right on or would I need fender modififation?

SIZE: 19 x 8"
PATTERN: 5 x 114.3 mm (4.5")
OFFSET: 50 mm

Tires: 245/45/19

kisel

sc400fb

I put my rims on finally. This is my set up 18x9 40offset 265/35/18 rear. 18x8 40 offset 255/35/18 front. No rubbing no spacers. Not sure how to add pics with it pm if u want to see

Sandlex2j

Ok so I got 19x9.5 up front wrapped in 255x40 and 19x10.5 wrapped in 275x40. My fenders are cut for maximum clearance. But I would like to lower my car to where the top tire tucks in to the lip if the rim. What size tires should I go with???