tjmhillz

iTrader: (6)

I tried searching but its well over 300pages lol. i thinking about picking up a set of Varrosteon ES3 specs are 18x8.5+22 and 18x9.5 +30 will these 1 clear ls400 brakes and 2 be flush. Im rolling on tein coils right now. also what size tire should i run. Im not into that stretch tire look because where i live the roads are horrible lol.

jadu

iTrader: (42)

These would fit nice. The rims would be flush with the fenders and all 4 fenders would need to be rolled completely flat

jadu

iTrader: (42)

18x9.5 +22 all around may be your best bet for a more flush look. It would allow you to run a 245 or 255 wide tire all around since the roads. As for clearing a BBK, this should clear it, but I would call the manufacturer just to make sure. I dont see any specs on the their disk on their wheels i.e. high, low, R, or A disk.

CatManD3W

iTrader: (18)

Thanks Jadu, The wheels are Volk GT-F in Satin Black Finish, would be real similar to when CalitriSC has them on the silver SC....

CalitriSC could you post some pics of the 19's on the silver SC?

CalitriSC

iTrader: (13)

Yea this was 19x9.5 +12 F and 19x10.5 +24 R

benjiSC3

Planning on running XXR 531 CCW reps
on STOCK suspension
18x9.5 +20
245 or 255
Guessing a minor roll will be fine

18x11 +20 with 275/35/18 (street tire) or 285/40/18 (DOT drag)
Guessing fenders will need to be rolled flat and slightly pulled
Can the rears be run without extra camber?

myLEXsc400

this fitment on a stock suspension is going to poke out a lot and look like major 4x4 status.

benjiSC3

Thnx for the advice!
I just downsized the wheels after going through this F**** 300+ page thread

18x8.5 +20 F
18x9.5 +20 R

square 255/45/18 which puts me a 26in tire height which is close to the stock 25.7 tire height.
Just decided to daily some cheap tires until i boost it
Eff pulling those double wall fenders

myLEXsc400

post up pics when you put the wheels on

Biddles

iTrader: (2)

Wow your car looks great man.

Sandlex2j

Hi guys. I'm new to club Lexus forums. I got a sandstone lexus sc300 on 19x9.5 front. 19x10.5 rear. Front tires are 255/40. Rear tires are 275/40. I got axis super hiro rims. My problem is that I got my fenders professionally cut and I still get some rubbing In the back (just a little) and my front I get a lot of rubbing when Turning. What tire size should I go with.

artboyyy11

Artboyyy11

Rim Brand and Type: Saleen Reps
Rim Size f/r: 18x9 18x10
Rim Offset f/r: top picture 30 WITH 15 mm spacers bottom: NO SPACERS
Tire Size f/r: 235/45/18 245/45/18
Suspension Setup: Espelir ASD Tokico blue
Comment On Ride: Slightly stiffer than stock. Love it.
Fender Modifications: Slightly rolled all around
Any other comments: No rubbing
Picture:


Read more: https://www.clublexus.com/forums/sc-...#ixzz2pCVNYJ6K

JesLet

iTrader: (19)

This is 10.5 x 18 +22

Sticking out about 1 inch, planning to put meaty tires preferably 295/30. Or is this gonna look weird?

Is 1-inch(could be less than 1-inch) pull doable with Eastwood fender roller?

JesLet

iTrader: (19)

One more thing since i want 295/30 i want the tires staright and no camber... what do you guys think?

gerrb

iTrader: (34)

Since you are not into stretched tires or what and you want 295 tires , with those 10.5" +22 , you will need a good pull and fender roll. Just like you said , the rim alone is already more than an inch out and the 295 tire will still budge a little bit further out. You know, I had those 10" +22 with 275 on the RM1 and I had to do that work on the quarter panels since they were out an inch . Now they are more than an inch inside with over 50mm pull with fender roll. I can fit in 335 or 325 easily.