MDSC

iTrader: (3)

i just cant help myself had a 25mm spacer laying around and tried it looks more like it, more low and more camber and i think it will just clear. that will make it +10.

8052JZ

iTrader: (13)

What tire size should I Run for this wheel fitment? I'm new to the whole wheel size and tire fitment deal.

95 SC300
Front: 19.8.5 +20
Rear: 19.9.5 +25

Car is lowered by springs but not sure how much.

thanks in advance

Novoken

iTrader: (5)

So going to get Works 18x8 front and 18.9 rear offset 38. Whats a good tire setup?

DWPsc3

iTrader: (10)

You should be able to fit a 245/35 tire for the rears if you fully roll or shave your rears. Heres mines when I was on Espiler ASD's

19x9.5 +22 Kumho Ecsta SPT's 245/35


For the fronts you can probably run a 235/35

Bender25

iTrader: (10)

My old Work Eurolines were almost identical to that sizing(18x8/9 +37) and i ran a 235/40 front and 255/35 rear. Was dropped on cut eibachs with no fender mods and it it only rubbed the rear fender liner when I had 4 people in the car. Looked like this-

Triple C

iTrader: (2)

So there is minimul rubbage and i have rolled it a little more and hammered int the Sneeky Inner fatter lip inside the well. I think i still have a little rubbage but its very small

Nice sunset on Saturday now its Freezing rain to snow
So this is the rear with an 18 x 10 XXR 521 245 x 40

Side View of the XXR I didnt have the suspension as low as i wanted it so i took them off and lowerd it a little more and put the RFP1's on wince they are my widest set.

Novoken

iTrader: (5)

hmmm you got anymore pics? How low was your drop?

scENFORCER

K guys, need your help!
I'm looking at a set of GT-C's for sale on another forum. Theyre 19x9.5 & 19x10.5 (+38f, +22r). Tires are 235f and 285r.

Will these fit the SC? Will it require any fender mods? (I'm guessing yes..) Planning to eventually lower on BC BR coils, not looking for it to be slammed.
If everything checks out and theyll fit my car I'm hoping to buy them asap!

Triple C

iTrader: (2)

your probably going to wan tto roll the fendor lip a little with a 285. the front will probably be ok

scENFORCER

^ do you think I'd be able to get away without doing it? Should I expect a lot of rubbing? Or just a bit?

Triple C

iTrader: (2)

Its all about the 285. If you put a 265 or 255 like i have you should be ok. The pics i have are 18 x 10.5 +12 in the rear and 8 x 9.5 +12 in the front. and dont be hesitant on rolling the fendor. I have used anything ROund that oyu can slip between the tire and well lip. then start Rolling it back by rolling the actuall bat or round thing against the fender lip you will know when it is bending cause it will freaking bend. Just dont go crazty like those guys who just throw a piece of pipe between the tire and lip and reverse to roll it. take your time and do it a little bit at a time. this is not a difficult project.

scENFORCER

Well, I'd be taking it to a shop to do it, wouldnt try it myself at all. My plan was to avoid rolling the fenders all together. Maybe I'll try selling the 285's and buy 255's just to be sure..
Thanks for the info though! I'm gonna go make an offer on these and see what happens.

CP_Ree

iTrader: (1)

18x10 + 15 up front lowered w/ a little tire tuck and probably lotsa camber.



18x10 +15 rear:

MDSC

iTrader: (3)

cp looks dope! feders pulled or just rolled?

gdoutlex

iTrader: (4)

CP REE, what size tires are you using?