Brake Booster Troubleshooting
Recently I removed my intake manifold to replace my knock sensors, wiring harness, rebuild the starter solenoid, and replace the injector O-rings. Once I got the car started again I began to have some issues. At first I had the Check VSC, VSC OFF messages on the dash but replacing the Engine Coolant Temp Sensor that I had busted cleared up that issue.
Unfortunately the problem I'm still experiencing is that the brake pedal has almost no travel and the BRAKE light remains on even after the parking break is released. Vacuum hose seems to be on there good. I had a few codes but after I cleared them with techstream none have returned. https://cimg6.ibsrv.net/gimg/www.clu...268c724c75.jpg Failed the first two test from the above picture. I haven't inspected the vacuum check valve but will momentarily. I just don't understand how the brake booster seemed to work fine before I removed the intake and then suddenly failed once I got the intake back on. I've gone over all the plug and hoses that I'd removed and all seem to be secured in the right locations. Anyone got any light to shed on my issues or should I just go ahead and start looking into replacing the Brake Booster assembly? |
Do you have vacuum in that booster hose with the car running? Yes, it will run like she-ot with the hose disconnected, but if you have someone start the car and you keep your thumb over the end of the hose, it will idle normally and you can get a feel for how much vacuum the engine is pulling through that hose.
That's where I'd start... |
Originally Posted by 2KHarrier
(Post 10232185)
Do you have vacuum in that booster hose with the car running? Yes, it will run like she-ot with the hose disconnected, but if you have someone start the car and you keep your thumb over the end of the hose, it will idle normally and you can get a feel for how much vacuum the engine is pulling through that hose.
That's where I'd start... |
Originally Posted by SlkySmooth
(Post 10232192)
Yes when I put my finger over the hose there was enough vacuum that I felt my finger getting sucked in. Couldn't say if it's weaker than it should be or not.
|
Originally Posted by 2KHarrier
(Post 10232221)
Well, without using a gauge, we can't be 100% sure, but I would have to assume you've got a problem someplace else. That should be plenty of vacuum to power the brake booster. Make sure the brake pedal moves freely (or as free as possible) with the engine off. It's just weird that all of a sudden you've got a new problem...
|
Two votes for getting a real vacuum gauge on it.
Any chance you had a plug or paper towel or something to plug the hose or manifold and left it in? Brake boosters are pretty hardy. It seems like something was missed and is not as it was. The engine runs and has vacuum. If the vacuum is available at the booster, you would hear a huge leak if it failed. I'd say it has no vacuum. |
I think autozone has a gauge I could rent. What does the vacuum need to be on the hose that goes to the brake booster?
|
At average altitude and normal idle, you should be able to see 17-21 inches of vacuum.
Not sure if this will help, but here's some very basic info on the system; http://library.alldatapro.com/alldat...1920/108921921 I tend to agree with 2013FSport. Something changed when you did the knock sensor and now you're seeing the results of that change. Let us know what the gauge reading states, and we'll go from there... If you have access to a vacuum pump, you could use that on the booster to see how the brakes feel, then you would be able to isolate the problem. It sounds strange, but another car could be used as the vacuum source, with a long enough hose... |
Well I borrowed a gauge from autozone, put it on the line going to the brake booster the needle didn't move at all. I guess that means I'm not getting enough vacuum I'm also noticing thethe car idling over 1k when I start it up. Not sure how to track down the a leak though
:uh: |
Originally Posted by SlkySmooth
(Post 10232840)
I'm also noticing the car idling over 1k when I start it up. Not sure how to track down the a leak though
:uh: Do it in short bursts though, not like you're spray painting a fender... Another thing that you can do is use a scanner with "Live Data" capabilities and watch the short term and long term fuel trims, known as STFT and LTFT. They should stay within 3% of 0 either side (+ or - 3.0%) If it goes too far into the positive (+10.0% to +25.0%) then you definitely have a vacuum leak somewhere and the engine is trying to compensate for it by adding more fuel, hence the higher idle speed. Here's a good tutorial on Fuel Trim; http://www.easterncatalytic.com/educ...agnostic-tool/ |
Originally Posted by SlkySmooth
(Post 10232840)
Well I borrowed a gauge from autozone, put it on the line going to the brake booster the needle didn't move at all. I guess that means I'm not getting enough vacuum
|
I just watched a clip of a vacuum/fuel pressure gauge in action and I'm pretty sure the one I rented is only for fuel pressure. :egads:
I tried something similar to what you described with propane rather than starting fluid, but I wasn't very patient or thorough with it as I had to leave for work. The high idle I noticed Is without disconnecting any hoses. I'm just now having somewhat of an "epiphany" and remembering that I noticed the PCV hose was cracked pretty good long before I took this project on. Perhaps the crack grew while I was moving things around. I ordered a new hose from the Toyota dealer down the street and a new PCV valve off amazon. I'll be crossing my fingers that the PCV hose is the culprit and I won't have to do too much more diagnosing but I'll still plan for the worst and read up on that link you sent me about fuel trim. I think I may as well try finding an affordable vacuum gauge while I'm waiting on the two parts. |
Glad to hear the update. Keep us posted as to what you find.
|
I've got some electric blue silicone tubing laying around from another car Im hoping will make a good replacement for a few of the vacuum hoses in the meanwhile. https://cimg6.ibsrv.net/gimg/www.clu...3c9d15e33e.jpg
Wish I could find a similar photo for my engine. |
Alright, so I got a vacuum gauge and the parts I mentioned in the mail today. Hooked it up to the hose going to the brake booster and what do ya know it went straight to 20 psi! I suppose that's a bit of good news at this point that I don't need to keep chasing a vacuum leak.
Does anyone have a professional/amateur opinion on this matter? I'm thinking this must mean the problem is in the brake booster? Perhaps it's out of alignment? |
All times are GMT -7. The time now is 12:51 PM. |
© 2024 MH Sub I, LLC dba Internet Brands