LS - 1st and 2nd Gen (1990-2000) Discussion topics related to the 1990 - 2000 Lexus LS400

What to check before buying a used LS400?

Old 02-13-19, 11:53 PM
Thread Starter
Join Date: Oct 2017
Location: CA
Posts: 151
Received 2 Likes on 2 Posts
Default What to check before buying a used LS400?

I'm looking at a 1999 LS 400 with 135k miles on it. Timing belt, water pump and struts done at 90k.
Engine and transmission mounts replaced at 100k
New starter done at 95k.

Rear diff replaced at 75k? Are there diff issues with these cars?

What else should I look at during inspection and for future repairs?
Hifiman1 is offline  
Old 02-14-19, 10:01 AM
Lexus Champion
Legender's Avatar
Join Date: May 2010
Location: TX
Posts: 1,839
Received 64 Likes on 63 Posts

Not sure I've ever seen a problem with the rear diff? That is new to me. My 98 as 227k miles on the original. Wonder if 3rd party shop took advantage of owner?

Most of key components look to be taken care of, struts are probably ready at that age/miles.

TB with water pump and seals and the mounts are the key things. Might check PS pump leaking on alternator as that is a known weak area.
Good luck.
Legender is offline  
Old 02-14-19, 11:54 AM
Lexus Champion
iTrader: (6)
timmy0tool's Avatar
Join Date: Sep 2008
Location: 909/626/714, SoCal
Posts: 4,845
Received 116 Likes on 108 Posts

never heard of a diff issue but if it's taken care of then great.
sounds like the rest of the maintenance was already taken care of, but you should ask for proof of work done.
anyone can take the seller's word for it, but show me the receipts!

the only place I would look is the leaking power steering pump which is common and have been covered here many times over.
timmy0tool is offline  
Old 02-14-19, 12:06 PM
Lead Lap
Join Date: Sep 2018
Location: California
Posts: 615
Received 20 Likes on 18 Posts

Cannot recall where I found it but I found this on these very forums and copied to a txt file.

The Unofficial LS400 buyer's guide
Good morning everyone. Since my LS is about to go into the shop again, I wanted to share my experience owning it and a GS400, creating a thorough buyer's guide since I see these questions pop up pretty often. Of course feel free to contribute any other tips you might have and maybe we can make this into a sticky post for potential buyers. Disclaimer: I'm not a professional mechanic nor do I work for Lexus. I'm just an enthusiast who loves these cars, obsesses over keeping them on the road in good condition and does a lot of DIY. I have an aerospace engineering background but no formal training on cars.


The most important items on the 1UZ engines are the timing belt and water pump. They should be changed every 90k-100k miles and there is a sticker under the hood, usually on the engine cover, that should state the date and mileage of the last change. 90-94 cars have a non-interference engine, meaning that if the timing belt jumps or snaps, your engine will just die but no mechanical damage will occur. 95+ engines are interference, so loss of timing will cause the pistons to hit the valves and result in catastrophic failure. When buying a 95+ car then timing belt change becomes more critical. It's good to do anyway because the water pumps start seeping around that mileage anyway. Make sure they change the idler pulleys, tensioner pulleys and hydraulic tensioner when they do the job or you do it yourself, 99% of shops will.

Cam seals and the crankshaft seals have a tendency to leak. You will notice by seeing an oily mess on the front of the engine, coming from behind the timing cover. In bad cases it will even drip on the ground. It is normally suggested to replace these while doing the timing belt and water pump service, so don't cheap out and ask for it to be done. 98+ cars also have a seal in the VVTi gear that can leak, so do that while you're there as well. I've had to do all three in three separate occasions (read: labor $$$$) because I was being a cheapskate and the shop I used wasn't keen on "while we're there" maintenance

Valve Cover Gaskets. These usually start to go around 60-80k depending on your luck. You will notice by a little wetness around the valve cover itself, or in really bad cases by dripping towards the rear of your engine. If it's really bad it will leak onto your hot catalytic converter releasing a puff of smoke when you're at a standstill. You can also pull a spark plug and see if it's oily as the spark plug tube seals usually fail at the same time and should be replaced as part of the job.

Vacuum recovery box. There's a plastic box along the intake tube that goes from your air filter to your throttle body on the 98+ cars to which several vacuum lines attach. The nipples for these lines are made of plastic and snap off on most cars, resulting in people jerry rigging hoses with RTV (I've even seen electrical tape!). You can check this easily by just removing the engine cover and taking a look. This can cause vacuum leaks and should be addressed. You can buy barbed brass fittings at the hardware store, drill out the hole where the old nipple was to enlarge it and screw the fitting in, putting some RTV around the joint for safety. Be careful not to crack the plastic in the process as it's very thin. Check the forums for detailed instructions on how to do this.

Hoses. Check them to make sure they're soft. With the age and heat most of these have gone hard and brittle. If you ever work on your car and plan to remove a hose, make sure to buy a replacement as it will crack when you pull it off.

Serpentine Belt. On high mileage cars check the tensioner and idler pulleys and make sure there's no bearing noise. They're cheap and easy to replace so I suggest doing it next time you change your belt on a high mileage car.


This warrants it's own sections as it's one of the biggest issues with these cars, especially the first generation ones. The main issue is that the pump will leak on almost all cars, and conveniently leak onto the alternator, frying it and leaving you without power. Make this the first thing you check on every car. First generation cars can also leak from the power steering reservoirs onto the alternator, but the reservoir location was moved I believe in 98. Also, if power steering fluid level drops but you don't see a leak, or if there's a puff of white smoke on startup, then you have a leak from the idle up valve that uses vacuum to raise the idle when the power steering pump is operated. It's screwed in to the pump and has two vacuum lines coming from it. You can read lots of info on the power steering system from the ClubLexus Power Steering Bible


The #1 suspension issue with these cars are the strut rod bushings. They usually fail around 100k miles and you can tell on the test drive if you're front end feels very loose over bumps. It can also cause a slight vibration when going 60-65 mph or a shimmy under light braking from highway speeds that will be felt in the steering wheel instead of in the pedal like warped rotors normally would.

Lower ball joints should also be replaced if the cars have over 100k. They're heavy cars and wear them out faster than other models. If grease is leaking from the boot, then it's time to replace. Grab the wheel at 12-6 and at 3-9 with the car jacked up and shake it. If there's play, then it's time to replace. You can do them when changing the strut rods as it's a pretty simple job compared to many other cars.

Sway Bar Bushings can also go bad. You can tell if there's a creaking noise going over bumps, like an old door opening. They're also cheap and take about 10 minutes each side to replace.


On 90-97 cars, the ECU capacitors tend to leak causing all sorts of crazy issues. The most common ones seem to be hard starting, rough running, OBD port that won't communicate. I personally have a 99 so I haven't experienced any issues, but there is a wealth of knowledge in this thread. The ECU can be rebuilt by a specialist either by mail-in or locally if you live around one, and it's not too expensive if I remember correctly.

The instrument cluster has two main failure modes. The LEDs on the needles can go out, leaving them dark, or the Speedometer and/or Tachometer needle will be stuck at zero. Both can be solved by sending it out for rebuild. There are several places in the US that offer this service for the LS400 and it's around 120$.

Corroded grounds can give funky electrical issues, including a no-start condition where the starter will click once then the whole car will just go dead as if there were no battery plugged in. It will usually start and work properly after pulling the negative battery terminal for a couple of minutes then connecting it back. You can follow the instructions on this thread to check the condition of your grounding points and replace any corroded component (part numbers are included). I had the intermittent no-start issue and replacing all parts in that thread cured it after a relatively straightforward fix.


The transmissions on these cars are very solid, and I haven't really experienced any pressing issues aside from these two things.

On the first drive of the day, it will hang in 2nd gear up until around 2600 RPM even if you're easy on the throttle then slam into 3rd. Just once. Afterwards it will never do it again. All the 1UZ Lexuses I've driven do this and the consensus seems to be that it's normal and can be programmed out by changing some components in the valve body. TransGo sells a kit online for around 70$ IIRC.

I've seen some cars throw a P0763 "Shift Solenoid C Electrical" code intermittently that will clear itself after one or two days. It seems to be more common on the GS400 and my GS did that a couple of times, but never on the LS. Could be possibly caused by a particle in some dirty transmission fluid getting stuck in the solenoid then clearing out and some have reported fixing it completely after a transmission flush, or some electrical contacts in the solenoid getting bent out of shape. On my GS draining and filling the fluid a few times only fixed it temporarily and it was resolved by replacing the solenoid.


Brakes on these cars don't seem to have any issues. If your car is a 90-94, consider upgrading to 95+ brakes as they are a lot more effective. It's a direct bolt on swap but you will need to run at least 17" wheels to clear the larger caliper and rotor.

Please feel free to contribute anything that I might have missed or not experienced, to make this guide as thorough as possible. Also feel free to correct me if I made any mistakes and I will edit as quickly as possible. Hopefully we can make a sticky thread out of this for future reference.


These have a big effect on the ride quality in the car.
A bad transmission mount can show itself in many ways but the most common one is a phantom like vibration you feel when accelerating through 1800-2000 RPM. It's a kind of flutter sound, similar to when you go high speed with the windows open but will be very difficult to discern and your passengers might not even feel it. I have very sensitive hearing so it bothered me a lot. You can also put your hand on the shifter and if you feel a vibration in that rev range, it's probably shot. Honestly it's probably shot anyway at high miles, costs around 50$ from the dealer and takes 30 minutes to change so there's no reason not to.
Engine mounts are more of a pain and I used a shop for mine. The 1UZ should be able to have a glass of water put on it's intake manifold and show no ripples. If it shows many ripples, or you feel lots of vibrations or a shaking at idle and when revving, even in neutral, then it's probably the mounts. All three of mine were split in half at 145k when they were changed.

EDIT: Added info on engine and trans mounts.
EDIT 2: Loaner LS400 that I tried also had the 2nd gear hanging issue in the morning so it is a design thing. Found the supplier of the valve body rebuild kit (TransGo) and edited accordingly.
EDIT 3: Added info on issues caused by corroded grounding points in the engine bay and how to check them
Sin1UZFE is offline  
Old 02-14-19, 01:56 PM
Lexus Champion
Stroock639's Avatar
Join Date: Apr 2012
Location: Long Island
Posts: 2,248
Received 72 Likes on 60 Posts

that's kinda weird that the starter and especially diff are already replaced... but oh well better for you

the only real "issues" apart from potentially leaking power steering are the suspension bushings getting worn out, and often the LCD for the radio will not be working

assuming the car doesn't have the nakamichi, the part# is CMW5077 from the pioneer parts store and can be replaced pretty easily in under an hour, assuming you have a 10mm with an extension and a little pry tool
Stroock639 is offline  
Old 02-14-19, 08:17 PM
Thread Starter
Join Date: Oct 2017
Location: CA
Posts: 151
Received 2 Likes on 2 Posts

The car is fully loaded with nachamichi stereo and heated seats. Color is mystic Jade.
Hifiman1 is offline  
Old 02-14-19, 08:43 PM
Lexus Champion
Stroock639's Avatar
Join Date: Apr 2012
Location: Long Island
Posts: 2,248
Received 72 Likes on 60 Posts

Originally Posted by Hifiman1 View Post
The car is fully loaded with nachamichi stereo and heated seats. Color is mystic Jade.
then you are indeed the hifi man... in that case i wish you the best of luck
Stroock639 is offline  
Old 02-15-19, 01:08 PM
Join Date: Mar 2018
Location: Colorado
Posts: 128
Received 12 Likes on 11 Posts

When was the timing belt actually replaced? My car only had 20k miles on it's belt, but it had been nearly 9 years old since it was last replaced because the previous owner hardly drove the thing.

Once it's at 7 or 8 years, regardless of how many miles, and especially since it's a post-95 where it's an interference motor, I'd recommend replacing it. You could possibly stretch it a bit more if most of the miles are highway and it's in a warm climate since that's easier on the systems.
400fanboy is offline  
Old 05-19-19, 04:30 PM
Driver School Candidate
Join Date: May 2019
Location: mn
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts

are there any specialty tools for the timing belt replacement on the 99 gs400? gear place holders or any of that jazz?
cheapass is offline  
Old 05-19-19, 05:20 PM
Pole Position
Peacebay's Avatar
Join Date: May 2018
Location: Ct
Posts: 385
Received 102 Likes on 78 Posts

Originally Posted by cheapass View Post
are there any specialty tools for the timing belt replacement on the 99 gs400? gear place holders or any of that jazz?
Negative on that
Peacebay is online now  
Old 05-19-19, 10:31 PM
Lexus Test Driver
lextout's Avatar
Join Date: Apr 2007
Location: seattle,wa
Posts: 1,213
Received 24 Likes on 24 Posts

its worth no more than 5000
lextout is offline  

Thread Tools
Search this Thread
Quick Reply: What to check before buying a used LS400?

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to and affiliated sites.
  • Ask a Question
    Get answers from community experts
Question Title:
Your question will be posted in: