ezzejacobs

iTrader: (1)

Well, the time has come for me to sell my car, which I am very sad to say. I have other priorities that I need to take care of in my life at this time. There has been a lot of parts changed on this car since I have owned it. I have all receipts to document what has been put into this car. Induction Performance out of Tampa, Florida is who has done all the work to the car. I highly recommend this shop to the buyer as they know the vehicle inside and out. It started off as an auto and was converted to a manual. The car has been tuned by one of the premier tuners in the nation at Induction Performance by Alpha. The car has made 771 on 25lbs and was running out of fuel pump on E85. This BEAST has not even reached its potential. So, I would like to first start off by listing what is currently in the car:

What is your First & Last name? Eric Jacobs
What is your Location? : Fort Myers, FL
VIN#:JTHBD192320047189
Miles:121,918
Price: $27,000 OBO
Title Status: Clean
Contact Info: Pm or reply on here, 239-777-5458
Description: 2002 Lexus IS300 Absolute Red with Black Alcantera
Interior with LSD Auto Converted to a 6 speed.
Engine: 1200hp built engine less than 3000 miles!
- Custom Induction Performance CP 10:1 Compression Piston Set 86.5mm Bore
- Upgraded Rings and Wrist Pins
- Carrillo HD H Beam Connecting Rods
- Carr Rod Bolts
- ACL Race Bearing Set
- ARP Main Studs
- ARP L19 Head Studs
- BC Titanium Springs & Retainers
- BC 264 cams
- SRT tubular Manifold
- Precision 6766 with .96ar and Antisurge H (large) Cover
- TIAL 44 mm waste gate
- Mild port job on head
- JDM GTE VVT-I valve covers, polished(HARD TO FIND)
- JDM GTE Engine cover painted to match
- TRD oil cap(real deal not ebay)
- Koyorad Aluminum Radiator
- Custom FFIM with Q45 TB, polished
- Tial 50MM BOV
- 12x24x3'' XS Power Intercooler (with T- Bolt Clamps)
- Ralco RZ Polished Pulley Kit
- Titan Motorsports ATI Crank Pulley
- Gates Timing Belt
- Machining, Bore & Hone Block, Set piston to wall clearance, resurface block, hot tank and clean block, balance and blueprint, pinfit pistons and rods, file fit rings, align bore and hone, spec all bearing clearances, clean and resurface head, install springs, retainers and new valve stem seals
Brad Penn 20w50 full synthetic is the only oil that I have used in the car since the new engine was put in. ( I do not recommend changing brands of oil )


Engine Management System
- Pro EFI 128 with V3 firmware update (rolling antilag, boost by gear, boost by rpm, etc...)
Package includes:
Pro128 Standalone ECU
IS300 Adapter Harness
5 Bar Map sensor
Wideband O2 sensor kit
Fuel Pressure 150psi sensor
iBoost control **** and solenoid (boost controller that allows you to change boost settings with a click of a ****. Has up to 5 different settings)
Optional equipment:
52mm CAN Gauge/Display
Flex Fuel Kit
Fuel
- SRT's 1000hp fuel rail, polished
- Injector Dynamics ID2000’s
- SRT's CNC Billet E85 compatible twin pump fuel hanger
- twin 340 DeatschWerks E85 compatible pumps
- full -6an lines and fittings
- Weldon A2040-281-A-120 fuel pressure regulator.
Transmission & Drivetrain
- V160 6speed
- Stock 6 speed shifter & ****
- Custom Suede Shift boot black with red stitching (not installed)
- Toyota Sequioa Driveshaft
RPS Billet Carbon Carbon Clutch & flywheel
- ARP flywheel bolts
- new slave, master and clutch line
Suspension and Aero Kit
Torsen LSD rear end
CX Racing Coilovers with 12K front springs and 10K rear springs suspension
Full Version select Body kit Rear bumper, Front Bumper, side skirts
Electronics
- Alpine 7.5" touch screen head unit
- rare electric 52mm electric Omori boost & EGT gauge with multi-color function (white, blue, green, red), which can be adjusted with a ****
Interior is all stock
Exhaust
full 3.5" heavy wall Aluminum exhaust from DP back. It uses mendral bent pieces fully fab'ed and tig welded with a vibrant aluminum muffler with 4" tip by Freed Engineering. Light weight and sounds awesome!
Car will come with:
- Ray Lexion 503's Wheels 19x9.5 rear 19x8 front


In addition have a set of 6 speed axles, GS400 diff, Weld RTS 15x10”, Hoosier 28x10.5 slicks (not mounted), extra trunk floor mat & carpet. I will include these parts for additional $1200 or will part these items out.
Also I wanted to say what is bad on the car. The front bumper has a broken tab on the drivers side, there are two areas where the bumper did not fit over the IC piping where the previous owner cut to allow clearance. There is damage on the passenger side where the mount tab is from not clearing a uhaul trailer when towing. There are a few dings and scratches on the car which for a 12 year old car is normal. There is a small oil leak from the oil pressure sensor on the engine, and the power steering return line is leaking near the pump due to relocation of the reservoir. Currently there is a clunking noise when accelerating which I am currently getting looked at. This will be resolved before the sale and delivery of vehicle.
Please do not ask me if I am parting out, because I am not looking to part the car. I am willing to sell the other items that are listed separate. I am only looking for serious inquiries, so no low ballers will require 10% deposit and remaining payment within 5 business days. I am willing to ship at buyers expense.

Again, if you have any questions please contact me.


Here is the same link on My.IS where if there is a question of creditability due to my low post I have several members who can vouch for me on the forum as well as My.IS and supraforums.


http://my.is/forums/f172/2002-absolu...9/#post7521913

Also here is a little video a few friends made when they had there first ride in this beast!!!
https://www.facebook.com/photo.php?v...type=2&theater
This was old dyno video making 743rwhp with old setup.
https://www.facebook.com/photo.php?v...type=2&theater

ezzejacobs

iTrader: (1)

Does anybody want a 800 hp IS300???

jasonson

Haha, I mean I definitely want one, but I'm still waiting for the suitcase full-o-money to show up at my front door.

Awesome work on the car Ezze, very boss to see an IS with slicks...... GLWS :-)

dexlex2002

good luck with the sale...the car looks great

PaCowboy

iTrader: (6)

Would u be interested In selling the drag slick setup? How much for the wheels and tires. What's the offset on the wheels?

Starquest

jdmek998

Please look at the date of when this was posted. 2014