|
Need HELP installing Tom's front lip !!!!!!!!!
3 Attachment(s)
Trying to install front lip and we have three big holes in front that do not line up with any holes in the body. Instructions are in Japanese . Anyone have any ideas .
|
ti it was mine...I would just make holes in those locations and use a bolt and washers( big ones ) and a nut ....which may require removing bumper cover....but u don't want to loose this at speed....its a nice lip
|
2 Attachment(s)
Originally Posted by rselby
ti it was mine...I would just make holes in those locations and use a bolt and washers( big ones ) and a nut ....which may require removing bumper cover....but u don't want to loose this at speed....its a nice lip
|
Originally Posted by I8ABMR
(Post 9696944)
I appreciate your input bro. I'm realizing that it may require more work than I can do. The body shop wanted to add screws and urethane it too. At this point I see where the estimate they gave me came from
|
I took my bumper off and drilled 3 holes in my bumper to align with the 3 big holes in the front part of the lip. Then you you need to drill 2 smaller holes to the left and right of each big hole in the bumper to attach the metal bracket shown in diagram #2 of the first pic you posted.
|
Originally Posted by KRISH
(Post 9697128)
I took my bumper off and drilled 3 holes in my bumper to align with the 3 big holes in the front part of the lip. Then you you need to drill 2 smaller holes to the left and right of each big hole in the bumper to attach the metal bracket shown in diagram #2 of the first pic you posted.
Also, I would recommend taping off around where the edge of the TOMS lip will be. The edges of the lip are pretty sharp, and as you're test fitting/installing, may scratch your paint. https://cimg5.ibsrv.net/gimg/www.clu...96e8a7b4e3.jpg -R |
I used 3 self tapping screws for those spots, similar to what Lexus uses with the built in washer, you can also drill a large hole and use a heavy duty plug similar to what is used to hold on the rear mud flap that sits in front of the back tire.
|
2 Attachment(s)
Originally Posted by JDMV8
all that garage space...and decor. You're lucky man :D
Originally Posted by KRISH
I took my bumper off and drilled 3 holes in my bumper to align with the 3 big holes in the front part of the lip. Then you you need to drill 2 smaller holes to the left and right of each big hole in the bumper to attach the metal bracket shown in diagram #2 of the first pic you posted.
Originally Posted by FNSSESPORT
I did exactly this, except I left the bumper on. It would be WAY easier removing the bumper to do this install. The LH and RH little metal brackets were easy to drill for, even with the bumper on. The centre bracket however, took me probably an hour, because space is tight. Also, if you have the headlight washers, watch out for the supply hose that runs along where you'll be drilling.
Also, I would recommend taping off around where the edge of the TOMS lip will be. The edges of the lip are pretty sharp, and as you're test fitting/installing, may scratch your paint. https://cimg5.ibsrv.net/gimg/www.clu...96e8a7b4e3.jpg -R
Originally Posted by ZaxF
I used 3 self tapping screws for those spots, similar to what Lexus uses with the built in washer, you can also drill a large hole and use a heavy duty plug similar to what is used to hold on the rear mud flap that sits in front of the back tire.
|
Looks great on MRM, Tammer! Can't wait to see you attack the road courses next year!
|
| All times are GMT -7. The time now is 06:40 AM. |
© 2026 MH Sub I, LLC dba Internet Brands