#FAQ: #Torque #Specs (Post #50 complete specs)
Thread Starter
Driver School Candidate
Joined: Aug 2019
Posts: 6
Likes: 3
From: CA
#FAQ: #Torque #Specs (Post #50 complete specs)
Edit: solved, and here is the info in case anyone needs it in the future:
Original post
I am installing a lift kit, and wanted to know the torque specs. I was hoping there exists a diagram like the one found here for the IX: https://www.clublexus.com/forums/sus...ere-first.html. I found specs in the factory service manual/TechDoc, but it's just a list and not a diagram. Does anyone know if a diagram like the one for the IX exists?
Specifically, for the front suspension I wanted to know the torque for:
Here is what the TechDoc has to say:
- strut lower bolt - 95 N*m / 70 ft*lb
- UCA to spindle (castle nut) - 110 N*m / 82 ft*lb
- tie rod end ball joint (castle nut) - 91 N*m / 67 ft*lb
- 3 x strut top plate to chassis frame - 64 N*m / 46 ft*lb
- rear shock absorber bottom bolt - 98 N*m / 72 ft*lb
- track rod ends (to frame chassis) - 110 N*m / 81 ft*lb
Original post
I am installing a lift kit, and wanted to know the torque specs. I was hoping there exists a diagram like the one found here for the IX: https://www.clublexus.com/forums/sus...ere-first.html. I found specs in the factory service manual/TechDoc, but it's just a list and not a diagram. Does anyone know if a diagram like the one for the IX exists?
Specifically, for the front suspension I wanted to know the torque for:
- strut lower bolt (this is the main one I can't figure out... on the IX diagram it is listed at 157 N*m)
- UCA to spindle (castle nut)
- tie rod end ball joint (castle nut)
- 3 x strut top plate to chassis frame (I believe this is 64 N*m)
Here is what the TechDoc has to say:
Last edited by vihila; Sep 9, 2019 at 11:44 PM. Reason: found the info
Popular Reply
Sep 29, 2021, 08:40 AM
CL Community Team
Joined: Mar 2017
Posts: 9,310
Likes: 3,968
From: USA
CL Community Team
Joined: Mar 2017
Posts: 9,310
Likes: 3,968
From: USA
••••••Check out Post #50 for substantial listing of all vehicle torque specs
In that same manual go into the Suspension Chapter. The area of "components" on each has diagrams
In that same manual go into the Suspension Chapter. The area of "components" on each has diagrams
Last edited by Acrad; Mar 30, 2023 at 01:57 PM.
Thread Starter
Driver School Candidate
Joined: Aug 2019
Posts: 6
Likes: 3
From: CA
I looked there, but I guess I didn’t look hard enough 
Edit: Yes, you are right! I looked under "Installation" and "Reassembly" but I didn't look under "Components". That's the secret sauce. Thanks so much @Acrad35751 !
Edit: Yes, you are right! I looked under "Installation" and "Reassembly" but I didn't look under "Components". That's the secret sauce. Thanks so much @Acrad35751 !
Last edited by vihila; Sep 9, 2019 at 02:15 PM.
Thread Starter
Driver School Candidate
Joined: Aug 2019
Posts: 6
Likes: 3
From: CA
For those who just want the details on these specific torque specs, they are as follows:
Anyone know the tie rod end castle nut spec?
Edit: N/M found it under the steering section - 91 N*m
- strut lower bolt - 95 N*m / 70 ft*lb
- UCA to spindle (castle nut) - 110 N*m / 82 ft*lb
- tie rod end ball joint (castle nut) - 91 N*m / 67 ft*lb
- 3 x strut top plate to chassis frame - 64 N*m / 46 ft*lb
Anyone know the tie rod end castle nut spec?
Edit: N/M found it under the steering section - 91 N*m
Pole Position
Joined: May 2010
Posts: 246
Likes: 78
From: CA
For those who just want the details on these specific torque specs, they are as follows:
Anyone know the tie rod end castle nut spec?
Edit: N/M found it under the steering section - 91 N*m
- strut lower bolt - 95 N*m / 70 ft*lb
- UCA to spindle (castle nut) - 110 N*m / 82 ft*lb
- tie rod end ball joint (castle nut) - 91 N*m / 67 ft*lb
- 3 x strut top plate to chassis frame - 64 N*m / 46 ft*lb
Anyone know the tie rod end castle nut spec?
Edit: N/M found it under the steering section - 91 N*m
CL Community Team
Joined: Mar 2017
Posts: 9,310
Likes: 3,968
From: USA
EDIT: 25 ft-lbs
I'm trying to find the torque specs myself for these brace brackets. The inner bolts are removed and replaced with flush bolts. It also sits under the Budbuilt skid after install. I can't seem to find the torque specs in FSM. I'll keep looking.
PNs: 5122535050 / 5122635070
Description: BRACKET, FRONT SUSPENSION MEMBER,
https://www.toyota-4runner.org/lexus...kid-gx460.html
I pulled this Pic of T4Fun's former '10 460 from 2011 4R forum post
I'm trying to find the torque specs myself for these brace brackets. The inner bolts are removed and replaced with flush bolts. It also sits under the Budbuilt skid after install. I can't seem to find the torque specs in FSM. I'll keep looking.
PNs: 5122535050 / 5122635070
Description: BRACKET, FRONT SUSPENSION MEMBER,
https://www.toyota-4runner.org/lexus...kid-gx460.html
I pulled this Pic of T4Fun's former '10 460 from 2011 4R forum post
Last edited by Acrad; Sep 11, 2019 at 03:54 PM.
Thread Starter
Driver School Candidate
Joined: Aug 2019
Posts: 6
Likes: 3
From: CA
I am doing the the Ironman 4x4 2" lift kit that is currently on sale for $699... I'll try to remember to let you know in a couple weeks how it is doing.
I have no idea where those specs would be, I don't see it in any of the obvious places (as I am sure you have looked as well). Good luck finding it!
Also (General FYI in case anyone comes back later and might find this useful) the rear shock absorber bottom bolt is 98 N*m / 72 ft*lb
I have no idea where those specs would be, I don't see it in any of the obvious places (as I am sure you have looked as well). Good luck finding it!
Also (General FYI in case anyone comes back later and might find this useful) the rear shock absorber bottom bolt is 98 N*m / 72 ft*lb
Trending Topics
Racer
Joined: Dec 2006
Posts: 1,727
Likes: 169
From: Nebraska
I am doing the the Ironman 4x4 2" lift kit that is currently on sale for $699... I'll try to remember to let you know in a couple weeks how it is doing.
I have no idea where those specs would be, I don't see it in any of the obvious places (as I am sure you have looked as well). Good luck finding it!
Also (General FYI in case anyone comes back later and might find this useful) the rear shock absorber bottom bolt is 98 N*m / 72 ft*lb
I have no idea where those specs would be, I don't see it in any of the obvious places (as I am sure you have looked as well). Good luck finding it!
Also (General FYI in case anyone comes back later and might find this useful) the rear shock absorber bottom bolt is 98 N*m / 72 ft*lb
ClubLexus Stories
Celebrating Lexus & Toyota from Around the Globe
8 Tips for Improving Your Hybrid or Plug-in Hybrid's Efficiency!
Michael S. Palmer
10 Best Lexus Models No One Remembers
Joe Kucinski
TRD Off-Road Premium: Best 2026 4Runner, Except This One Thing
Michael S. Palmer
Top 10 Lexus & Toyotas to Drive Before You Die!
Joe Kucinski
Top 10 Lexus/Toyotas With The LEAST 5-Year Depreciation
Joe Kucinski
Lexus LC500 Convertible Auction: A Preview of Rising Values?
Brett Foote
GX 550 vs TX 550: Best 3-Row Luxury Lexus Family Hauler
Michael S. Palmer
9 Best Lexus Models You Can Buy for Half Price (And 1 You Shouldn't!)
Joe Kucinski
2026 Lexus NX Buyer's Guide: Models, Features, Prices & More!
Brett Foote
CL Community Team
Joined: Mar 2017
Posts: 9,310
Likes: 3,968
From: USA
FAQ: Torque Specs
3 x Strut top plate to chassis frame: 64 Nm / 46 ft-lb
Bracket, Front Suspension Member: 25 ft-lbs (pic)
Caliper slider bolts: 65 ft-lb (for replacing brake pads)
Differential Front Fill: 29 ft-lb
Differential Front Drain: 48 ft-lb
Differential Rear Fill: 36 ft-lb
Differential Rear Drain: 36 ft-lb
Oil Drain plug: 30 ft-lb
Oil Filter cap metal: 18.43-22.13 ft-lb
Oil Filter cap plastic: 18 ft-lb
Oil filter end plug (metal oil cap mod): 9-10 ft-lb
Rear shock absorber bottom bolt: 98 Nm / 72 ft-lb
Skid plate for oil filter access: 21 ft-lb
Spark Plugs: 15 ft-lbs
Strut lower bolt: 95 Nm / 70 ft-lb
Tie rod end ball joint (castle nut): 91 Nm / 67 ft-lb
Track rod ends (to frame chassis): 110 Nm / 81 ft-lb
Transfer Case Drain: 27 ft-lb
Transfer Case Fill: 27 ft-lb
Transmission Check Valve: 15 ft-lb (many have sided closer to 10 ft-lb)
Transmission Drain Plug: 15 ft-lb (many have sided closer to 10 ft-lb)
Transmission Fill Plug: 29 ft-lb
UCA to spindle (castle nut): 110 Nm / 82 ft-lb
Wheel lugs: 83 ft-lb
[Front Suspension Torque Specifications]
Bracket, Front Suspension Member: 25 ft-lbs (pic)
Caliper slider bolts: 65 ft-lb (for replacing brake pads)
Differential Front Fill: 29 ft-lb
Differential Front Drain: 48 ft-lb
Differential Rear Fill: 36 ft-lb
Differential Rear Drain: 36 ft-lb
Oil Drain plug: 30 ft-lb
Oil Filter cap metal: 18.43-22.13 ft-lb
Oil Filter cap plastic: 18 ft-lb
Oil filter end plug (metal oil cap mod): 9-10 ft-lb
Rear shock absorber bottom bolt: 98 Nm / 72 ft-lb
Skid plate for oil filter access: 21 ft-lb
Spark Plugs: 15 ft-lbs
Strut lower bolt: 95 Nm / 70 ft-lb
Tie rod end ball joint (castle nut): 91 Nm / 67 ft-lb
Track rod ends (to frame chassis): 110 Nm / 81 ft-lb
Transfer Case Drain: 27 ft-lb
Transfer Case Fill: 27 ft-lb
Transmission Check Valve: 15 ft-lb (many have sided closer to 10 ft-lb)
Transmission Drain Plug: 15 ft-lb (many have sided closer to 10 ft-lb)
Transmission Fill Plug: 29 ft-lb
UCA to spindle (castle nut): 110 Nm / 82 ft-lb
Wheel lugs: 83 ft-lb
[Front Suspension Torque Specifications]
Last edited by Acrad; Jun 16, 2020 at 04:11 PM.
Pit Crew
Joined: Oct 2019
Posts: 186
Likes: 164
From: Colorado
Pole Position
Joined: Oct 2019
Posts: 266
Likes: 73
From: MN
Drive shaft Torque Nut and Bolts
I believe this has been mentioned before, but wanted to know what tools people are using to torque the nuts and bolts on the driveshaft.
I thought a longer style of socket would work, but now sure what people are doing for this service?
Thank you
I thought a longer style of socket would work, but now sure what people are doing for this service?
Thank you
Racer
Joined: Jan 2011
Posts: 1,761
Likes: 248
From: AZ
Exploded diagram of brakes front and back with torque specs?
I found the FAQ that had a listing a lot of the torque specs, just curious if anyone has a factory exploded diagram for this generation GX with all the torque values front and back for a brake job.
Was planning to do a front and back brake job.
Was planning to do a front and back brake job.
