Regarding the data I saw about EMPS using techstream, I don't know if this is correct
#1
10th Gear
Thread Starter
Regarding the data I saw about EMPS using techstream, I don't know if this is correct
As you can see in the picture, the angle of my torque sensor is not 0, and it will change when I turn the direction, but when the steering wheel is in the middle position, it displays the data as shown in the picture. I don't know if this is correct, should they be 0 degrees?
There are also other data in this picture. I don’t know if there is any wrong data. I hope someone who can understand can solve my doubts.
There are also other data in this picture. I don’t know if there is any wrong data. I hope someone who can understand can solve my doubts.
#3
#4
You reference some pictures in your post. I understood that to mean there were supposed to be some pictures attached in your post. I was just letting you know that at least for me, no pictures showed up in your post.
EDIT:
Oh weird. I switched connection and now the page loads. Disregard my post.
Last edited by EAST; 02-13-23 at 07:51 AM.
#5
You reference some pictures in your post. I understood that to mean there were supposed to be some pictures attached in your post. I was just letting you know that at least for me, no pictures showed up in your post.
EDIT:
Oh weird. I switched connection and now the page loads. Disregard my post.
Trending Topics
#9
Posting what mine was doing. They were both around the 270ish degrees mark for torque sensor 1 and 2. But honestly it changes around a lot. In the picture attached it ended up being 0 and 358. I couldn't tell if slow constant torque to the wheel was the same as quick turning motions because of the slow refresh rate.
If you click the graph at the bottom, it'll graph it out a value (you double click what you want). But, mine would only sample ever 5 to 10 seconds, which was annoying. The graph is just turning the wheel left to right then right to left. If I left the wheel anywhere without moving or touching it, it would remain at that value. Basically that was my only take away: if you left the wheel in any position, centered (not holding it applying some torque), it would stay relatively constant at whatever value it was at.
Sorry for the phone pictures. I had screenshots but laptop kept crashing towards the end (it's old).
If you click the graph at the bottom, it'll graph it out a value (you double click what you want). But, mine would only sample ever 5 to 10 seconds, which was annoying. The graph is just turning the wheel left to right then right to left. If I left the wheel anywhere without moving or touching it, it would remain at that value. Basically that was my only take away: if you left the wheel in any position, centered (not holding it applying some torque), it would stay relatively constant at whatever value it was at.
Sorry for the phone pictures. I had screenshots but laptop kept crashing towards the end (it's old).
#10
Looking again at both your picture and mine, I wonder if the value under your red square (trq1,2 zero point value) is the actually the "zero" or center point. For mine 274.6 and 273.1 are the zero point, which matches with the 270ish observation. And your 64 is close to the 61 you have.
Granted I don't know what sets that zero point value.
Granted I don't know what sets that zero point value.
#11
Lexus Champion
iTrader: (1)
I have Techstream also. Currently the laptop that I have it loaded on is in the shop. So I can't look at this.
You may want to ask this on the GSF, RCF, ISF or 2nd Gen IS forum. They are a lot more knowledgeable about Techstream and more use it there. There are also some Toy/Lex shop Tech on those forums also. They can likely help a little more with this.
You may want to ask this on the GSF, RCF, ISF or 2nd Gen IS forum. They are a lot more knowledgeable about Techstream and more use it there. There are also some Toy/Lex shop Tech on those forums also. They can likely help a little more with this.
#12
10th Gear
Thread Starter
Looking again at both your picture and mine, I wonder if the value under your red square (trq1,2 zero point value) is the actually the "zero" or center point. For mine 274.6 and 273.1 are the zero point, which matches with the 270ish observation. And your 64 is close to the 61 you have.
Granted I don't know what sets that zero point value.
Granted I don't know what sets that zero point value.
Thread
Thread Starter
Forum
Replies
Last Post
LexFather
Car Chat
12
05-16-09 10:06 AM