ES300 Coilover install Worklog
#31
Lead Lap
iTrader: (1)
I've learned with the ES that it's better to install the fronts first...the coilovers won't go as low in the front, so if you put the fronts on first, you'll have a better idea of what kinda of stance you want. The rear coils will always go lower than the front (you can tuck the whole rear wheel under the fender), so adjust the stance in front first, then the rear. It will save you alot of time.
#32
Pole Position
Thread Starter
iTrader: (1)
Join Date: Oct 2004
Location: MD Smitty runs da City
Posts: 3,002
Likes: 0
Received 5 Likes
on
5 Posts
But here is a camber plate.
-Smitty
#33
Pole Position
Thread Starter
iTrader: (1)
Join Date: Oct 2004
Location: MD Smitty runs da City
Posts: 3,002
Likes: 0
Received 5 Likes
on
5 Posts
And now for the finale. The front. The fronts were so much easier than the rears. Easy to remove and put back one. Pretty much comes off like the rears but it seems so much shorter for some reason Well here goes
Remove tires of course
Loosen the brakeline holder
Loosen and remove the two strut bolts
Forgot to take a picture but pop the hook and remove the 3 nuts on the top of the strut.
Remove tires of course
Loosen the brakeline holder
Loosen and remove the two strut bolts
Forgot to take a picture but pop the hook and remove the 3 nuts on the top of the strut.
#35
Pole Position
Thread Starter
iTrader: (1)
Join Date: Oct 2004
Location: MD Smitty runs da City
Posts: 3,002
Likes: 0
Received 5 Likes
on
5 Posts
Smitty Tip :
If you have them where gloves. Keeps you from banging the skin off your knuckles and keeps the grime off your hands and nails. Forgot to do this for the rears. hehe
If you have them where gloves. Keeps you from banging the skin off your knuckles and keeps the grime off your hands and nails. Forgot to do this for the rears. hehe
#36
Pole Position
Thread Starter
iTrader: (1)
Join Date: Oct 2004
Location: MD Smitty runs da City
Posts: 3,002
Likes: 0
Received 5 Likes
on
5 Posts
Carefully measure the height and adjustment of both coilovers to ensure they are the exact same.
Put everything back together and double check to make sure everything is tightened
Call a friend over to help you and double check your work. Sometimes its better to have another set of eyes on something. And besides you can always you an extra hand. In my case it was BernieIS
Put everything back together and double check to make sure everything is tightened
Call a friend over to help you and double check your work. Sometimes its better to have another set of eyes on something. And besides you can always you an extra hand. In my case it was BernieIS
#38
Pole Position
Thread Starter
iTrader: (1)
Join Date: Oct 2004
Location: MD Smitty runs da City
Posts: 3,002
Likes: 0
Received 5 Likes
on
5 Posts
Well thats it. I'm finally finished. I actually adjusted the camber and height a little more in the front. Dropped it down a little more. I must say it rides pretty well. It is stiff but not too bad of a ride. I've only driven the car roughly 5-10 miles.
Smitty Tip :
After any wheel/tire and suspension modification be sure to get an alignment. Not getting an alignment after suspension mods could result in uneven tire wear and/or even worse damage to your suspension.
I will be taking pictures tomorrow of the drop after my alignment. I'll also be taking pictures this weekend at a carshow I will be attending in Lebanon, PA. If you're in the area and not busy you should come out and kick it with us
-Smitty
Smitty Tip :
After any wheel/tire and suspension modification be sure to get an alignment. Not getting an alignment after suspension mods could result in uneven tire wear and/or even worse damage to your suspension.
I will be taking pictures tomorrow of the drop after my alignment. I'll also be taking pictures this weekend at a carshow I will be attending in Lebanon, PA. If you're in the area and not busy you should come out and kick it with us
-Smitty
#41
Probably one of the best and most detailed writeup's I have seen here on the boards in a long while. Excellent work Smitty. Now quit teasing the people, get some finished product shots of the car and make the ES moderators sticky this thread.