When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
So when are you moving to the South so you can enjoy that monster car you have ?
Tell me about it man. The midwest weather suck most of the year, literally have like a month of "good" weather here. Planning on visiting Texas this summer.
Irving - if this project is still on , I guess the modifications that needs to be done based on observations given here would be
* Blue - keep the roundness
* Yellow - flared out symmetrically and gradually from the top center of the arch to get the wheel inside those yellow areas while it is flushed from the top center (meaning both 10 and 2 o'clock should have same amount of flaring , not only the front part which is near the front bumper ) .
* One last suggestion from me if it is not too hard to do is having tabs on that fender (just like what the stock fender has) so we can bolt or screw on a splash shield we need to fabricate to protect the wires there and prevent mud and water slinging all over that area .
If 50mm front fender is too much for the stock APTech bumper and side skirt then 25mm should be fine. It will already allow us to install Deep Dish Wheels to make the car look good as seen below. Consequently we can get in wider and meaty tires at the same time..... Function and Looks together
I got my vented fenders a while back but haven't installed them. It will be a while before I get them on the car since I plan to buy the APT body kit as well. Plus my SC's ecu is blown out and it's battery is dead so i can't get anything done right now.
I meant to post in here a while back but I was without a computer and can't stand typing on my phone.
You're welcome! Sorry that I didn't get back to you on that last one. I'm debating on if I should get the rear fenders too. The idea having deep dish wheels with big tires is appealing.
You're welcome! Sorry that I didn't get back to you on that last one. I'm debating on if I should get the rear fenders too. The idea having deep dish wheels with big tires is appealing.
No big deal buddy ! The picture I have posted above .... an SC with the AC Kit , Wide Body with Deep Dish Wheels just did it for me. It is subtle and still classy looking. It doesn't seem to be riced out for me.
No big deal buddy ! The picture I have posted above .... an SC with the AC Kit , Wide Body with Deep Dish Wheels just did it for me. It is subtle and still classy looking. It doesn't seem to be riced out for me.
That SC you posted looks amazing. I would like a subtle look like that. I need to figure out what size wheels and offsets to get with these 50mm fenders.
Irving we haven't heard from you about this front fenders . Just wondering if you still have plans of modifying them to take care of the concerns mentioned on this thread ?
Sorry for being gone for so long. Tons of projects in the works as well as some health concerns have set me back a bit, but I'm back in action.
To update this thread, we have not done any modifications to the molds at this time. What i am planning on offering on a very limited basis is a modified version of the fenders, however i do not currently have an ETA on that.
Some updated installed images for your viewing pleasures:
A group of Arizona guys got together and ordered a ton of fenders:
I dunno, I think that jade green stock width one looks way better
If you can't sense the sarcasm, that's my car lol. But I was going to ask if you produce a front lip similar to the Wise one I have on my car. It's fiberglass has a couple small cracks in it and would like to maybe consider getting a poly lip. Do you sell a lip for us 92 front bumper folks at all?
I dunno, I think that jade green stock width one looks way better
If you can't sense the sarcasm, that's my car lol. But I was going to ask if you produce a front lip similar to the Wise one I have on my car. It's fiberglass has a couple small cracks in it and would like to maybe consider getting a poly lip. Do you sell a lip for us 92 front bumper folks at all?
. Well you have a gorgeous car, it's really clean, almost sleeper status (except for the FMIC lol).
I currently don't make any lips for the 92 crowd , and am currently booked until November with projects.
01-20-17, 03:48 AM
![Name: round1b2_zpszk35ppmm.jpg
Views: 827
Size: 241.5 KB](https://www.clublexus.com/forums/"http://s1010.photobucket.com/user/gerrb/media/3rdSC4002jzgteProject/round1b2_zpszk35ppmm.jpg.html")
!
. Just wondering if you still have plans of modifying them to take care of the concerns mentioned on this thread ?
. Well you have a gorgeous car, it's really clean, almost sleeper status (except for the FMIC lol). 
, and am currently booked until November with projects.