specONE Build Thread
#181
Driver School Candidate
Thank you posting your armrest organizer tray! I had a hard time figuring out how to organize my coins and random crap in my car. Had no idea this was available until your post! Just ordered mine all thanks to you.
The following users liked this post:
LexoticJ (05-11-17)
#184
#185
Racer
Thread Starter
iTrader: (3)
had some time today to get the fog lights in.
turns on there is absolutely no way I was getting them on without removing the front wheels.
They have to be stuff in from the back side to bolt on.
Luckily I had a little more free time than i initially put aside for it today
turns on there is absolutely no way I was getting them on without removing the front wheels.
They have to be stuff in from the back side to bolt on.
Luckily I had a little more free time than i initially put aside for it today
#186
These OEM fog lights are awesome. I have them also and the guy who'd installed mine said it was hell of a job to do. He had to take several parts off of the car. It took him a few days to do.
Your car looks killer, as usual.
Your car looks killer, as usual.
#189
Racer
Thread Starter
iTrader: (3)
commence the itchy posts
used a cardboard template to figure out the bottom of the subwoofer enclosure. Cardboard easier to cut and do over if I mess up rather that do it on wood
now to trace it onto the wood
now taping commences to protect the trunk lining
bottom wood test fit
Time to protect the rest of the vehicle so the Fiberglass resin does not get all over the place
First layer of resin and mat laid
used a cardboard template to figure out the bottom of the subwoofer enclosure. Cardboard easier to cut and do over if I mess up rather that do it on wood
now to trace it onto the wood
now taping commences to protect the trunk lining
bottom wood test fit
Time to protect the rest of the vehicle so the Fiberglass resin does not get all over the place
First layer of resin and mat laid
#190
Racer
Thread Starter
iTrader: (3)
now that it is dry, time to get it out
and boy did it give me a workout pulling on it to release it. Struggled for a good 40-50 minutes pulling and yanking and spraying water into the crevice to weaken the blue masking tape adhesive.
my trunk is still intact and not a mess after pulling the mold
Took a half hour of peeling the blue tape off the rear of the mold, very tedious activity
quick test fit back in the car
up next will be to add another layer or two to this to strengthen the walls some more before i trim the piece down. right now the mold is a bit oversized and not easy to remove in and out of vehicle. Then onto figuring out how the front will look .
hopefully i can keep the momentum of this project going,
if not expect a update in a couple of months lol.
and boy did it give me a workout pulling on it to release it. Struggled for a good 40-50 minutes pulling and yanking and spraying water into the crevice to weaken the blue masking tape adhesive.
my trunk is still intact and not a mess after pulling the mold
Took a half hour of peeling the blue tape off the rear of the mold, very tedious activity
quick test fit back in the car
up next will be to add another layer or two to this to strengthen the walls some more before i trim the piece down. right now the mold is a bit oversized and not easy to remove in and out of vehicle. Then onto figuring out how the front will look .
hopefully i can keep the momentum of this project going,
if not expect a update in a couple of months lol.
Last edited by specONE; 05-02-16 at 09:46 PM.
#194
#195
Nice!!
-Josh
-Josh
__________________
Your #1 Dealer for Aftermarket Performance Products
Orange County, CA
Email: info@merakiautoworks.com
Text/Call: 213 394 2886
Website: www.MerakiAutoworks.com
Your #1 Dealer for Aftermarket Performance Products
Orange County, CA
Email: info@merakiautoworks.com
Text/Call: 213 394 2886
Website: www.MerakiAutoworks.com