Build Threads Details on Club Lexus SC owner vehicles

My SC300 build log!

Old 08-09-13, 08:36 AM
  #1  
mikef
Lexus Test Driver
Thread Starter
iTrader: (3)
 
mikef's Avatar
 
Join Date: Jun 2013
Location: CO
Posts: 875
Received 3 Likes on 3 Posts
Default My SC300 build log!

Hey everyone, I'm new around here and I wanted to share some of the things i started, Ill be updating this thread a lot in the next few years or so, any comments is much appreciated

2JZ GTE V160 Parts List complete

6-speed drive belt tensioner
16620-46070 tensioner list 243.36 cost 182.52
16621-46010 bracket list 50.22 cost 37.66
16622-46010 arm list 23.96 cost 17.97
16602-46010 shock absorber list 77.66 cost 58.24
91511-g0845 bolt list 1.24 cost .93 x 2
90901-16001 stud list 2.79 cost 2.09
90179-08171 nut list 1.21 cost .91 x 2
90116-08348 stud list 1.15 cost .86 x 3
90080-17242 nut list 1.78 cost 1.33 ex x 2
Transmission
33030-0w212 v160 assy new $6300
31123-14020 inspection cover cost 30.38
31121-14030 inspection cover cost 36.65
90080-11228 bolt cost 3.28 total x 4
08885-01306 v160 oil qt cost ea x 2 Check to see if its prefilled/ checked ok
57255-14231 CROSS MEMBER, cost 173.23
90980-11051 Toyota HOUSING, CONNECTOR F cost 5.19
82998-12440 terminal for the housing connectorsx2
58261-14010 upper trans tunnel cost 80.33
90159-A0045 Screw, W/washer 2.92
12371-46110 trans mount list 87.92 cost 65.94
Shifter
33504-14130 shift **** cost 92.08
33511-14031 control shaft cost 25.86
33513-22030 yoke cost 7.87
33530-14442 93.5-95 short throw shifter cost 133.56
90301-11015 o ring cost 12.16 total x 4
33531-14010 boot cost 40.42
90387-08134 collar cost 4.22 total x 2
33555-14110 boot cost 38.38
33555-14100 boot cost 10.17
33556-14050 seat cost 1.63
33057-14010 bracket cost 45.94
33570-14070 shifter tri-pod cost 97.65
93381-16016 bolt cost 3.04 total x 4
90179-08095 nut cost 2.46 total x 2
90105-08200 bolt cost 2.06 total x 2
91651-60835 bolt cost 6.08 total x 4
90105-08076 bolt cost .79
90179-08233 nut cost 1.03
90250-06026 pin cost 1.18
90467-21010 clip cost 2.46
33546-22020 bushing cost 29.00 ea x 2
Clutch parts/pedals
SC300/SC400 5 speed conversion pedal set $355
58280-14080 boot/plate assy list 25.72 cost 24.33
SC300 Manual Shifter Boot $58
31470-14060 slave cylinder list 83.38 cost 62.53
90080-10055 bolt list 1.21 cost .91 x 2
31410-14310 master cylinder list 150.31 cost 112.73
90179-08237 nut list 1.24 cost .93 ea x 2
31481-14260 tube list 32.07 cost 24.05
96816-50335 hose list 31.09 cost 23.32
31484-24010 bracket list 8.48 cost 6.36
31482-14060 tube list 15.00 cost 11.25
90119-06406 bolt list 1.01 cost .76
96991-10080 clip list 1.58 cost 1.18 ea x 2
90119-06733 bolt list .95 cost .71
00475-1BF03 brake fluid pint list 5.81 cost 4.36 ea x 2
90363-12002-77 BEARING,PILOT LIST 8.65 COST 6.49
96152-00500 RING, SNAP LIST 3.36 COST 2.52
90903-63001 BEARING , RELEASE LIST 81.00 COST 60.75
90560-50001 SPACER LIST 7.36 COST 5.52
90560-79001 SPACER LIST 3.02 COST 2.26
90206-12006 WASHER, LIST 2.01 COST 1.51
90520-75001 RING, SNAP LIST 3.74 COST 2.80
31264-14060 SPRING, LIST 3.74 COST 2.80
31231-14050 HUB, LIST 44.28 COST 33.21
31204-14060 FORK LIST 88.70 COST 66.52
90119-08079 BOLT, COVER LIST 0.75 COST 0.56 EA X 6
90910-02115 BOLT FW LIST 12.18 COST 9.13 EA X 8
13450-0W011 FLYWHEEL LIST 831.35 COST 623.51
31210-14170-84 REMAN COVER LIST 174.02 COST 139.61 [ includes 7.00 core charge ]
steering reservoir. 44360-24042


ClutchMasters 16000-HD00-R FX100 Stage 1 Clutch Kit Toyota Supra $660
RPS Cyn-R-G Aluminum Segmented Flywheel for 1993-98 Supra TT BF-22170 $474.05


Rear Differential/Driveshaft/Axles
Diff JDM 3.26 LSD supra $1500
Custom driveshaft $375
Rubber rear driveshaft coupling from supra TT 37511-30020 COUPLING, FLEXIBLE cost $307.06 price $228.72
42340-14140 lh drive axle list 568.87 cost 426.65
42330-24030 SHAFT ASSY, RR DRIVE cost $437.10 price $325.58
Oil pressure sensor mod / Gauges
90401-19008 union bolt $33
90430-20016 Gasket $1.28
90301-68005 O-ring $3.67
VDO-360086 Sender press 100PSI 1/8 $32.29
VDO-350106 Gauge press 100PSI CV $44.99
VDO-150121 Gauge Turbo Mech 30HG-25 $59.99
Auto Meter 3222 Nylon Tubing$6.72
1/8 NPT TO 1/8 BSPT $11.21
T-FITTING ADAPTER FOR BOOST GAUGES POWERSTROKE MAP LINE BOOST LINE 1/8NPT DIESEL
VDO-150851
Fuel Pump
Walbro 255 in tank fuel pump with setup kit $100 plus ECU fuel pump $49


Engine
2JZ GTE supra swap $3930 with cat
Tial 50mm Q Blow Off Valve $260
CX Racing Intercooler for 1993-1998 Toyota soaror $494.10

Other
fipg sealant $20.50
Fan Shroud for supra 92-00 $199.00
MIO-MMRADSUPT Radiator $285.00

KW V3 Coilovers $2000

Sc300 $6000

Wheels $1407

New old stock floor mats $200

95 tail lights $150

LS400/Supra TT rear calipers and goodridge lines and R1 rotors $1250

gallon toyota red coolant
clutch fluid and power steering fluid

Grand total $29500 with no labor cost








My SC300 build log!-3k23f83n35n15m15t6d6r1e7a106da9f31ea1.jpg

My SC300 build log!-3k53jf3h55k35s15q1d6rf38e617e16eb1389.jpg

My SC300 build log!-3ra3j93n15n15g45sbd6r9c9cc5e4424f1e3a.jpg

Last edited by mikef; 03-05-15 at 05:51 PM.
Old 08-09-13, 09:27 AM
  #2  
1JZPWRD
1JZ Single SC400
iTrader: (59)
 
1JZPWRD's Avatar
 
Join Date: Jan 2009
Location: Alabama, Roll Tide!
Posts: 8,518
Likes: 0
Received 15 Likes on 12 Posts
Default

Did you buy new wheels???

If you have all the manual parts, what are you waiting for? LOL
Lets get busy!!!!
Old 08-09-13, 09:29 AM
  #3  
mikef
Lexus Test Driver
Thread Starter
iTrader: (3)
 
mikef's Avatar
 
Join Date: Jun 2013
Location: CO
Posts: 875
Received 3 Likes on 3 Posts
Default

KWs
My SC300 build log!-20130729_183848.jpg


My SC300 build log!-20140228_142923-2-.jpg

My SC300 build log!-20131218_161356.jpg

My SC300 build log!-20140228_142941.jpg
new home
My SC300 build log!-20140402_141139.jpg

Last edited by mikef; 07-24-14 at 05:40 PM.
Old 08-09-13, 10:28 AM
  #4  
BAD954BOI
Lexus Champion
iTrader: (5)
 
BAD954BOI's Avatar
 
Join Date: Jun 2009
Location: fl
Posts: 1,751
Likes: 0
Received 1 Like on 1 Post
Default

Now I'm tempted to just do my cluster myself
Old 08-09-13, 10:34 AM
  #5  
mikef
Lexus Test Driver
Thread Starter
iTrader: (3)
 
mikef's Avatar
 
Join Date: Jun 2013
Location: CO
Posts: 875
Received 3 Likes on 3 Posts
Default

Parts
My SC300 build log!-20131119_130233.jpg

Last edited by mikef; 07-24-14 at 05:41 PM.
Old 08-09-13, 03:06 PM
  #6  
dmthomas9
Driver School Candidate
 
dmthomas9's Avatar
 
Join Date: May 2013
Location: OR
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default

Did you take pictures while you were doing your cluster? I want to re do mine as well. And where did you get the LED's? I havent done much research on it yet cause I have a few things I want to do first.
Old 08-09-13, 03:11 PM
  #7  
mikef
Lexus Test Driver
Thread Starter
iTrader: (3)
 
mikef's Avatar
 
Join Date: Jun 2013
Location: CO
Posts: 875
Received 3 Likes on 3 Posts
Default

No but I should of, sorry. ill link you the LEDs I used but I don't mind doing them for you if your not good at soldering
Its the same way the other guys do it on ebay when you have to ship your cluster out, I can only get white or warm leds. They dim to

Last edited by mikef; 08-09-13 at 03:16 PM.
Old 08-09-13, 05:06 PM
  #8  
93Gotjuice
Pole Position
iTrader: (6)
 
93Gotjuice's Avatar
 
Join Date: Dec 2012
Location: Socal* *
Posts: 361
Likes: 0
Received 0 Likes on 0 Posts
Default

On a great start buddy
Old 08-09-13, 05:22 PM
  #9  
mikef
Lexus Test Driver
Thread Starter
iTrader: (3)
 
mikef's Avatar
 
Join Date: Jun 2013
Location: CO
Posts: 875
Received 3 Likes on 3 Posts
Default

just got my wheels


front 18x8.5 + 35 225/40/18
rear 18x9.5 +35 255/35/18

will be installing them tomorrow

My SC300 build log!-20130809_200833.jpg

Last edited by mikef; 08-10-13 at 05:38 AM.
Old 08-10-13, 01:15 PM
  #10  
dmthomas9
Driver School Candidate
 
dmthomas9's Avatar
 
Join Date: May 2013
Location: OR
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default

Where Do you live? im not bad at soldering but its been a long time. you in the northwest?
Old 08-10-13, 01:15 PM
  #11  
dmthomas9
Driver School Candidate
 
dmthomas9's Avatar
 
Join Date: May 2013
Location: OR
Posts: 22
Likes: 0
Received 0 Likes on 0 Posts
Default

Nice Wheels BTW.
Old 08-10-13, 09:29 PM
  #12  
mikef
Lexus Test Driver
Thread Starter
iTrader: (3)
 
mikef's Avatar
 
Join Date: Jun 2013
Location: CO
Posts: 875
Received 3 Likes on 3 Posts
Default

Here's your LEDs, they fit perfect in the back of the needles but you have to remove your old ones first
http://www.oznium.com/diamond-led-strip
Old 08-11-13, 07:25 AM
  #13  
lilSCsteve
Moderator
iTrader: (71)
 
lilSCsteve's Avatar
 
Join Date: Sep 2008
Location: NC
Posts: 3,235
Received 10 Likes on 8 Posts
Default

Mikef, you're off to a great start bro! I'm diggin the wheels too! Nice touch with the center trim makeover!

steve
Old 08-12-13, 08:39 AM
  #14  
mikef
Lexus Test Driver
Thread Starter
iTrader: (3)
 
mikef's Avatar
 
Join Date: Jun 2013
Location: CO
Posts: 875
Received 3 Likes on 3 Posts
Default

wheels on!!

My SC300 build log!-20130812_104236.jpg

My SC300 build log!-20130812_104207.jpg

My SC300 build log!-20130812_104219.jpg

My SC300 build log!-20130812_104227.jpg
Attached Thumbnails My SC300 build log!-20130812_104313.jpg  

Last edited by mikef; 08-12-13 at 02:42 PM.
Old 08-12-13, 09:02 AM
  #15  
1JZPWRD
1JZ Single SC400
iTrader: (59)
 
1JZPWRD's Avatar
 
Join Date: Jan 2009
Location: Alabama, Roll Tide!
Posts: 8,518
Likes: 0
Received 15 Likes on 12 Posts
Default

Its a amazing how well just buy adding a drop and new wheels makes a huge difference. Nice touch man.

Whats next???

Thread Tools
Search this Thread
Quick Reply: My SC300 build log!



All times are GMT -7. The time now is 06:41 PM.