MD FS: Joe Z Intake - BLUE SPECIAL EDITION- NEW!
08-11-11, 06:14 PM
#1
FS: Joe Z Intake - BLUE SPECIAL EDITION- NEW!
SOLD! Thanks For Your Interest!
Joe Z Intake - Special Edition Blue - $100 + shipping
BRAND NEW
NEVER USED
COST ME JUST UNDER $150 shipped
Here is some info on this part from L-Tuned Parts
This part is suitable for the following models:
2007-2010 IS250
2006-2010 IS350
Dress up your engine and gain power while you are at it with this 3" Special Edition Blue Satin Finish Aluminum Intake Pipe specifically designed for your IS250, IS250awd, IS350 & IS C Models.
** ALSO FITS THE 06+ GS350 AND GS450h **
The Direct Air Flow Intake (D-AFI) Pipe is constructed of 6061-T4 aluminum which has been mandrel bent and polished to a fine luster. The Black Finish pipes have gone through a special process and are completed in a Satin Black Anodized Finish for that stealthy OEM look!!
Independent DYNO Test results on a stock IS350 have shown gains of 5+ Rwhp Max Power & 5+ ft.lbs of Peak Torque.
The stock manual 6 speed IS250 showed gains of 6+ Rwhp Max Power & 5.6+ ft.lbs of Peak Torque.
This pipe replaces the factory plastic tube of the stock intake system, fully utilizing the stock air box. The intake pipe inner surface has a smooth design that will give your oem system optimal air flow with out any disruptions.
No need for Tuning and NO Check Engine Lights..!!
Included are Silicone sleeves available only in Black. Also, four Brushed Stainless Steel clamps along with simple to follow install directions, will make this intake swap a breeze.
" Designed by an Enthusiast for Enthusiasts "
100% Made in the USA
Joe Z Intake - Special Edition Blue - $100 + shipping
BRAND NEW
NEVER USED
COST ME JUST UNDER $150 shipped
Here is some info on this part from L-Tuned Parts
This part is suitable for the following models:
2007-2010 IS250
2006-2010 IS350
Dress up your engine and gain power while you are at it with this 3" Special Edition Blue Satin Finish Aluminum Intake Pipe specifically designed for your IS250, IS250awd, IS350 & IS C Models.
** ALSO FITS THE 06+ GS350 AND GS450h **
The Direct Air Flow Intake (D-AFI) Pipe is constructed of 6061-T4 aluminum which has been mandrel bent and polished to a fine luster. The Black Finish pipes have gone through a special process and are completed in a Satin Black Anodized Finish for that stealthy OEM look!!
Independent DYNO Test results on a stock IS350 have shown gains of 5+ Rwhp Max Power & 5+ ft.lbs of Peak Torque.
The stock manual 6 speed IS250 showed gains of 6+ Rwhp Max Power & 5.6+ ft.lbs of Peak Torque.
This pipe replaces the factory plastic tube of the stock intake system, fully utilizing the stock air box. The intake pipe inner surface has a smooth design that will give your oem system optimal air flow with out any disruptions.
No need for Tuning and NO Check Engine Lights..!!
Included are Silicone sleeves available only in Black. Also, four Brushed Stainless Steel clamps along with simple to follow install directions, will make this intake swap a breeze.
" Designed by an Enthusiast for Enthusiasts "
100% Made in the USA
Last edited by timgs300; 08-12-11 at 06:46 PM.
Thread
Thread Starter
Forum
Replies
Last Post
gemini1
2Gen IS250 / IS350 / IS-F Classifieds (06-13)
1
10-30-17 02:59 PM
bboysunone
2Gen IS250 / IS350 / IS-F Classifieds (06-13)
0
07-05-16 05:11 PM
