TX FS: NA-T Turbo Kit + 2JZ SC300 Parts
05-16-09, 09:03 PM
#1
Lexus Test Driver
Thread Starter
iTrader: (2)
Join Date: Feb 2004
Location: Behind you
Posts: 1,509
Likes: 0
Received 0 Likes
on
0 Posts
FS: NA-T Turbo Kit + 2JZ SC300 Parts
Contact: Sales@JackyPerformance.com
All parts are from this PERSONAL 1995 Lexus SC300 (unless noted otherwise) and this is NOT a commercialized AD of any kind and the parts are from my personal ownership:
This is a dyno of another user of the same base turbo kit with same T67 sized turbo and .63 a/r exhaust housing.
PT67 turbo @ 20psi made 463.6 rwhp and 454.4 ft/lbs tq:
Base Turbo Kit has been sold, here are the remaining parts:
6. 4'' Polished aluminum Intake
7. 4'' Sbpower.com Air Filter
8. Silicone Couplers + T-bolt clamps
9. Intake Manifold-- Drilled & Tapped w/ vacuum fittings (ensures pure uninterrupted vacuum sources)
10. Y-Plenum w/ EGR Block-Off Plate & Vacuum caps
11. 3 Extra Authentic Tial Wastegate Springs (5.8psi-Red / 7.25psi-Green / 8.7-Blue)
12. Custom Intercooler Kit (Vertical setup with Spearco-style core)
--> All Ends of Intercooler Piping are beaded to prevent coupler blow-off under boost.
--> Authentic HKS SSQV BOV flange installed on piping (includes O-Ring Seal and clip)
--> AEM Air Inlet Temperature hole is threaded, tapped, and ready for the AEM AIT sensor.
--> Thermotec Reflective heat wrap on cold side intercooler piping that sits above turbo
--> This Short intercooler piping promotes less lag & better response.
13. Misc Vaccum hose & Fittings
14. Boostwerx Oil Feed Line + Union Bolt
15. Remote Oil Filter setup for turbo (ensures turbo always gets clean oil) = prolongs turbo life
--> includes threaded hole for sensor of your choice (like pressure / temp / etc)
16. Thermo-Tec heatwrap (new remainder roll)
17. All Nuts, Bolts, Washers, and Gaskets are included to make this kit plug & play.
Everything shown in the pictures is part of the kit and sale, except the jack stands and props used to hold them up.
All parts are from this PERSONAL 1995 Lexus SC300 (unless noted otherwise) and this is NOT a commercialized AD of any kind and the parts are from my personal ownership:
This is a dyno of another user of the same base turbo kit with same T67 sized turbo and .63 a/r exhaust housing.
PT67 turbo @ 20psi made 463.6 rwhp and 454.4 ft/lbs tq:
Base Turbo Kit has been sold, here are the remaining parts:
6. 4'' Polished aluminum Intake
7. 4'' Sbpower.com Air Filter
8. Silicone Couplers + T-bolt clamps
9. Intake Manifold-- Drilled & Tapped w/ vacuum fittings (ensures pure uninterrupted vacuum sources)
10. Y-Plenum w/ EGR Block-Off Plate & Vacuum caps
11. 3 Extra Authentic Tial Wastegate Springs (5.8psi-Red / 7.25psi-Green / 8.7-Blue)
12. Custom Intercooler Kit (Vertical setup with Spearco-style core)
--> All Ends of Intercooler Piping are beaded to prevent coupler blow-off under boost.
--> Authentic HKS SSQV BOV flange installed on piping (includes O-Ring Seal and clip)
--> AEM Air Inlet Temperature hole is threaded, tapped, and ready for the AEM AIT sensor.
--> Thermotec Reflective heat wrap on cold side intercooler piping that sits above turbo
--> This Short intercooler piping promotes less lag & better response.
13. Misc Vaccum hose & Fittings
14. Boostwerx Oil Feed Line + Union Bolt
15. Remote Oil Filter setup for turbo (ensures turbo always gets clean oil) = prolongs turbo life
--> includes threaded hole for sensor of your choice (like pressure / temp / etc)
16. Thermo-Tec heatwrap (new remainder roll)
17. All Nuts, Bolts, Washers, and Gaskets are included to make this kit plug & play.
Everything shown in the pictures is part of the kit and sale, except the jack stands and props used to hold them up.
Last edited by dejacky; 02-20-10 at 03:30 PM.
05-16-09, 09:07 PM
#2
Lexus Test Driver
Thread Starter
iTrader: (2)
Join Date: Feb 2004
Location: Behind you
Posts: 1,509
Likes: 0
Received 0 Likes
on
0 Posts
------------------------------------------------------------------------------------------
Stock OEM Lexus SC300 Parts For Sale Are Below This Line
------------------------------------------------------------------------------------------
*Rear Differential: $100
Last edited by dejacky; 02-17-10 at 01:17 PM.
05-16-09, 09:11 PM
#3
Lexus Test Driver
Thread Starter
iTrader: (2)
Join Date: Feb 2004
Location: Behind you
Posts: 1,509
Likes: 0
Received 0 Likes
on
0 Posts
*Front Brakes (Rotors + Calipers + Pads): $75
*Supra mkiv Springs (69,000 mileage): $60
*Catback Exhaust: $40
*2JZ-GE stock Exhaust manifold (2 pieces): $10
*Supra mkiv Springs (69,000 mileage): $60
*Catback Exhaust: $40
*2JZ-GE stock Exhaust manifold (2 pieces): $10
Last edited by dejacky; 03-06-10 at 11:47 AM.
05-16-09, 10:38 PM
#6
Lexus Test Driver
Thread Starter
iTrader: (2)
Join Date: Feb 2004
Location: Behind you
Posts: 1,509
Likes: 0
Received 0 Likes
on
0 Posts
Mteele, I have no idea how much shipping is at this point, but if anyone else can give you an estimate it might help both of us. I'll ship it the cheapest way that is easiest for you. It's already off the car, so it's not a big hassle to get an estimate, but earliest I can check is Friday-Saturday of next week.
Trending Topics
05-23-09, 06:43 PM
#8
Driver School Candidate
iTrader: (1)
Join Date: Jul 2008
Location: Tucson, AZ
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Hi, do you happen to have the front cat. "The y-pipe that is after the header". I need it to de-cat and fit on my stock header. And why in TX are you staying. I live in DFW. My cell # 4694269023.
thks.
Jon
thks.
Jon
05-23-09, 11:03 PM
#9
Lexus Test Driver
Thread Starter
iTrader: (2)
Join Date: Feb 2004
Location: Behind you
Posts: 1,509
Likes: 0
Received 0 Likes
on
0 Posts
Mteele, I'll update this post with the dimensions and weight of the oem stock exhaust so you can get accurate shipping estimates from shipper of your choice. That is the best I can do.
05-24-09, 07:59 AM
#12
Hello,
If you don't ship the exhaust to the member in North Carolina I will purchase it from you. I am in San Antonio, Texas and could pick it up. Please let me know.
Thanks,
Luis E. Velez
210 573 1271
levelezmd@yahoo.com
If you don't ship the exhaust to the member in North Carolina I will purchase it from you. I am in San Antonio, Texas and could pick it up. Please let me know.
Thanks,
Luis E. Velez
210 573 1271
levelezmd@yahoo.com
