Fog light HID installed
#1
Lexus Test Driver
Thread Starter
Fog light HID installed
Hi folks.. I'm just wondering how did you guys install the HID on your fog lights? I was torn at the begining as I didn't want to leave the housing open. I thought that I'd have to break the back cover apart then all of a sudden I came up with an idea
Well, its probably have been done but this is what I did.
Lots of pix.. bare with me...
Enjoy!!!
Well, its probably have been done but this is what I did.
Lots of pix.. bare with me...
Enjoy!!!
#4
Lead Lap
iTrader: (2)
Join Date: May 2009
Location: VA
Posts: 557
Likes: 0
Received 0 Likes
on
0 Posts
Good idea personally I cut a big hole in the center cap big enough for the bulb to fit then use the rubber stopped to silicone it (well i tried my cut was to jagged and off and that raised top piece I didnt cut out and after I tried it was so jagged. So I went with a staple gun and stapled it closed. Works great a little condensation during rain but thats about it.
#5
Lexus Test Driver
Thread Starter
Last set of pix...
Now I feel better... Tried to make it as clean as possible... All pix are off driver side. I pretty much did the same on passenger side.
#6
Lexus Test Driver
Thread Starter
Thanks 24boosted and nfordhk. I did somewhat seal it with heat glue but just the corner. Need to buy silicon to put around the wires....
HID from DDM. Thought I try their ApexCone Raptor one then maybe next time i'll buy the slim ballast.
HID from DDM. Thought I try their ApexCone Raptor one then maybe next time i'll buy the slim ballast.
#7
Lexus Champion
iTrader: (27)
Wow you got the ballast to sit up there? Nice i put mine on the crash bad? Yeah i was stumped on how to put the wires in also. Where did you ground it exactly? I put mines in other slot of the cap ( really bad at describing) and i just zipped tied it. I didn't silicone it or anything i left a small opening. It just hit spring in So-cal so shouldn't have to worry about condensation for awhile
I got the exact same kit too! Its a little bluer than i like but its nice.
I got the exact same kit too! Its a little bluer than i like but its nice.
Trending Topics
#9
Lexus Test Driver
Thread Starter
Wow you got the ballast to sit up there? Nice i put mine on the crash bad? Yeah i was stumped on how to put the wires in also. Where did you ground it exactly? I put mines in other slot of the cap ( really bad at describing) and i just zipped tied it. I didn't silicone it or anything i left a small opening. It just hit spring in So-cal so shouldn't have to worry about condensation for awhile
I got the exact same kit too! Its a little bluer than i like but its nice.
I got the exact same kit too! Its a little bluer than i like but its nice.
#11
Lexus Test Driver
Thread Starter
Oh yeah... I got 55W 5000K for lowbeam headlight and 35W 5000K for the fogs.... The fogs do look bluish. Couldn't quite see how it looks since its day time. I guess we'll see tonight.
#12
Lexus Champion
iTrader: (27)
wow its bluish at 5000k? Mines are 6000k and they are pretty blue too bad the fogs housing project the light everywhere so it isn't concentrated in one spot.. I accidently cut one of the rubber weather thing QQ but yeah it held up fine. The double side that DDM gives you SUCKS! I mounted both of them and went for a drive and they ballast fell off, luckily i had some extra 3m double side leftover
6000k 55watts for low beams and 6000k for fogs 35watt
Thats the way i did it.
6000k 55watts for low beams and 6000k for fogs 35watt
Thats the way i did it.
Last edited by abounly; 03-20-10 at 01:59 PM.