How realiable are factory roof rack cross bars?
#1
Driver School Candidate
Thread Starter
Join Date: Jan 2005
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
How realiable are factory roof rack cross bars?
I bought a yakima bike rack and a set of 23H Mighty Mounts for my 2005 RX330. I installed the set on the factory installed roof rack cross bars. However, after mounting my mountain bike, I noticed that there is quite a play on the cross bars particulary where the cross bars mate with the fastening/locking mechanism on each end onto the roof rack. It does not give me a good feeling that it will hold the weight of the bike.
Has anyone used this setup on the RX330?
would appreciate your inputs.
emmy
Has anyone used this setup on the RX330?
would appreciate your inputs.
emmy
#3
MultiTasking Mom
no complaints either; i have the thule ski/snowboard pullout racks.
i know what you mean about the "play" on the sides, but i think they are pretty secure, because the crossbars lock into place at each notch, and cannot be moved without lifting the slide handle. i had yakimas on my old RX300, and those things were a lot scarier - you would have to twist the **** so tight, and even then, sometimes they would fly towards the back; scared the living daylight out of me going 80+ on highway! the old crossbar system didn't have the parallel support, and no notches to lock into.
i know what you mean about the "play" on the sides, but i think they are pretty secure, because the crossbars lock into place at each notch, and cannot be moved without lifting the slide handle. i had yakimas on my old RX300, and those things were a lot scarier - you would have to twist the **** so tight, and even then, sometimes they would fly towards the back; scared the living daylight out of me going 80+ on highway! the old crossbar system didn't have the parallel support, and no notches to lock into.
#4
Driver School Candidate
Thread Starter
Join Date: Jan 2005
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
thank you both for your responses. Carrying a bike I guess is different because of the height, it appears less stable. At any rate I found that the looseness or play of the cross bars is mainly due to the spring loaded locking mechanism on one end ( passenger side), and secondarily due to the fact that the cross bars are not really fastened tightly on the rails but rather secured by being inside the rail channels and using pins on each end.
For peace of mind, I adjusted the spring loaded ends to max length, unscrewed the torx screws, added a washer and screwed the torx screw back tightly to prevent any movement. This resulted to a snug fit of the cross bars onto the rail channels and significantly reduced the movement or looseness even after loading a bike onto the bike rack....I think I am ok now...
For peace of mind, I adjusted the spring loaded ends to max length, unscrewed the torx screws, added a washer and screwed the torx screw back tightly to prevent any movement. This resulted to a snug fit of the cross bars onto the rail channels and significantly reduced the movement or looseness even after loading a bike onto the bike rack....I think I am ok now...
#5
Driver School Candidate
Join Date: Apr 2011
Location: MN
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
thank you both for your responses. Carrying a bike I guess is different because of the height, it appears less stable. At any rate I found that the looseness or play of the cross bars is mainly due to the spring loaded locking mechanism on one end ( passenger side), and secondarily due to the fact that the cross bars are not really fastened tightly on the rails but rather secured by being inside the rail channels and using pins on each end.
For peace of mind, I adjusted the spring loaded ends to max length, unscrewed the torx screws, added a washer and screwed the torx screw back tightly to prevent any movement. This resulted to a snug fit of the cross bars onto the rail channels and significantly reduced the movement or looseness even after loading a bike onto the bike rack....I think I am ok now...
For peace of mind, I adjusted the spring loaded ends to max length, unscrewed the torx screws, added a washer and screwed the torx screw back tightly to prevent any movement. This resulted to a snug fit of the cross bars onto the rail channels and significantly reduced the movement or looseness even after loading a bike onto the bike rack....I think I am ok now...
I know it has bee a while since you posted this, buth thanks!
Thread
Thread Starter
Forum
Replies
Last Post
peewhy
3Gen GS460 / 450H / 430 / 350 / 300 Classifieds (06-12)
0
07-01-16 04:58 PM