Acceleration Problems after Dealer Oil Change
#61
Moderator
Well it hasn't improved at all. It cruises just fine on the freeway and responds well to throttle. But from a stop and up to about 40 mph......Yikes. I took it to a local Toyota dealer and the service advisor went for a ride with me. He agreed there's a problem. He advises to make an appt and have them hook up to Techstream. There's also a noise associated with the symptoms. It's sort of like a rattle or vibration from the exhaust (I think). He heard it too. He wonders if the exhaust is plugged. He said if it were his car, he'd disconnect the tailpipes and see of the prob goes away. For now, I'll see if the issue goes away after a few more days. FWIW, I hooked up a code scanner and there are no codes, nor are any pending. The trans also has no codes. This is why he suspects exhaust. If it were ping, timing related (or fuel, etc) it would set a code.
#62
Cure
Has happened to me too. Uncouple your positive battery cable for 30 minutes. Has worked every time for me.
Hard to believe that an oil change could lead to that, but my experience shows it's not a coincidence
Hard to believe that an oil change could lead to that, but my experience shows it's not a coincidence
#63
What you're doing with 1/2 hour disconnect is taking charge off any and all the capacitors in the system.
Quicker (and maybe more sure) way - if you like - is to pull (+) and (-) cables, and once
disconnected from battery, touch one to the other. You're now sure all charge is gone.
Has worked for me on my old 328 convertible.
#64
Jesus Christ, at least I'm not alone.
Had my first oil change performed 2 days ago, and noticed the car is extremely slow when accelerating. When pressing the accelerator, it feels like the car weights 10 tons or more - the engine starts making a loud noise (like it always used to) but it takes 3-5 seconds for a real acceleration to begin.
Hope it will fix itself after driving for some time.
Had my first oil change performed 2 days ago, and noticed the car is extremely slow when accelerating. When pressing the accelerator, it feels like the car weights 10 tons or more - the engine starts making a loud noise (like it always used to) but it takes 3-5 seconds for a real acceleration to begin.
Hope it will fix itself after driving for some time.
The following users liked this post:
DrQuality (08-05-21)
#69
I use 5W30 since this type of oil was used by dealer previously.
By the way, I noticed the same thing as some other people: the car is responsible when driving at higher speeds, but accelerating at lower speeds is mission impossible.
I also noticed (did some tests during weekend) that my car still accelerates very well at low speeds when it's cold. If I start the engine after night, no problems at all. However, acceleration problem occurs several minutes later.
By the way, I noticed the same thing as some other people: the car is responsible when driving at higher speeds, but accelerating at lower speeds is mission impossible.
I also noticed (did some tests during weekend) that my car still accelerates very well at low speeds when it's cold. If I start the engine after night, no problems at all. However, acceleration problem occurs several minutes later.
#70
Lexus Test Driver
Interesting.... well for economy purposes you can use 0w-20w. But I have did one oil change myself and havent experienced this. Just curious if this oil weight related or not...
#71
Lexus Fanatic
5W20 synth for me. That's what's on my cap and what was used by my dealer previously.
MANXP: are you sure it's 5w30 and not 5w20?? That weight is not recommended by Lexus.
For gits and shiggles I'm going to try non synth at my next change. I'll be shocked if it has any effect, but worth a go.
I will also try and reset my ECU by disconnecting the battery. However, it's my understanding that this will not reset it as there is a built in power supply (much like a computer motherboard has).
MANXP: are you sure it's 5w30 and not 5w20?? That weight is not recommended by Lexus.
For gits and shiggles I'm going to try non synth at my next change. I'll be shocked if it has any effect, but worth a go.
I will also try and reset my ECU by disconnecting the battery. However, it's my understanding that this will not reset it as there is a built in power supply (much like a computer motherboard has).
Last edited by roadfrog; 05-19-14 at 07:17 AM.