Go Back   Club Lexus Forums > Lexus Model Forums > LS Models > LS430
Sign in using an external account
Register Forgot Password?

LS 430 Hood Release Cable Replacement DIY

Reply
 
 
 
 
Thread Tools Search this Thread Display Modes
Old 01-12-14, 03:11 PM   #1
BT3100
Rookie
Trader Score: (0)
 
Join Date: Sep 2010
Location: PA
Posts: 96
Exclamation LS 430 Hood Release Cable Replacement DIY

Just replaced the hood release cable in my 02' LS 430.
I should have taken some pics but did not.

A few weeks back my hood started giving me trouble latching down.
I took apart the hatch and all looked good inside. Sprayed some Boesheild on her and it worked for a about week.
The cabled needed to be replaced. The lever under the dash was not springing back.. For the last week when I needed to get under the hood I used a thin rod to jiggle the latch until I heard the "click" that it was ready to lock the hood.

Picked up an OEM cable on Ebay for $35.

First step is to remove the latch. There are 4 10MM nuts holding the latch. Two of these nuts hold the center support bar (Dead center of the radiator). Remove all 4. One of these nuts is capped with a plastic black cover.

Next step is to remove the right side horn. One 12mm nut and it will come off.

Once it's off you now have access to the final 10MM nut needed to free up the latch to get to the cable end. Once this nut (also capped off with a plastic cover) is removed you can begin to remove the latch. You will see the back side of a plastic clip below the left most nut on the latch. Push this forward and the latch will pull out and down.

You will now have access to the latch. Push the latch towards the right side of the car and you will now have enough slack to remove the ball end on the cable.

On the LS the cable runs under the rail supports just behind the head light, down the drivers side of the engine compartment and into the fire wall. Pull the cable out of the three clips holding to the frame of the car.

Here is a trick....... Stand at the center of the drivers side front wheel and with heavy wire cutters, cut the cable in half. This will help with fishing the cable back out to the latch.

At this point head under your dash and below your steering wheel remove the black cover ( it holds your OBD port). Only three screws and few electrical connections need to be removed here.

Once this cover is out you can pull out the half cable through the firewall. Don't try to use it to fish the new one in. Tried that.. did not work.

I tried a few different ways to fish the cable into the cabin. Here is the only method that worked.

Take a wire clothes hanger and cut the top section off so you are left with one long straight piece.
Push 3/4 of the length of the hanger through the firewall (hole in the black boot). You will now see it under the dash. Back to under the hood. With pliers create a SMALL loop in the hanger (think small enough to make it through the hole in the boot. Before you close the loop, pass the cabin lever end of the cable into the loop, camp down on the loop to lock in the cable. This will allow you to pull the cabin end through the boot. Before you try to pull the ball through the boot spray a good lube on the boot and let it sit for 5 minutes. Back under the dash pull the hanger and cable through the dash and reconnect to the lever.

Now tape the other side (latch side) of the cable to the section that you cut, leading to the latch. Fish the cable through the rails back to the latch.

Reconnect the cable to the latch and reinstall the latch.

Total time was 1:20. This included about 20 minutes of failed efforts to fish the cable through the firewall.

There is a good DIY for this project on a GS on this board... I used this... but on the LS you do not need to remove the front tire as the cable runs up top.

Good Luck. And enjoy your properly working hood release!
This ad is not displayed to registered members.
Register your free account today and become a member on Club Lexus!
__________________
Every part on your car is broken, you just don't know it yet...
BT3100 is offline   Reply With Quote
Old 01-12-14, 04:47 PM   #2
HiloDB1
Lexus Test Driver
Trader Score: (3)
 
HiloDB1's Avatar
 
Join Date: Jun 2010
Location: Hawaii
Posts: 865
Default

Thanks for the write up. I have to do this soon as my latch sticks on occasion.
__________________
HiloDB1 is offline   Reply With Quote
Old 01-12-14, 07:53 PM   #3
nDrew
Pole Position
Trader Score: (1)
 
nDrew's Avatar
 
Join Date: Feb 2006
Location: Ga
Posts: 215
Facebook.com/ndrewnugen Heartxandxsoles HeartAndSoles
Send a message via AIM to nDrew
Default

Thanks for the write-up. Fortunately I don't need this thread yet however if I ever do I will be grateful for this.
nDrew is offline   Reply With Quote
Old 03-27-14, 03:45 PM   #4
Tom57
Pole Position
Trader Score: (0)
 
Join Date: Mar 2008
Location: Illinois
Posts: 329
Default

BT, Thank you for this clear DIY instructions ... more helpful than the "hood lock control" cable removal in the LS manual. Also, nice to have easy access to the engine bay again! As these LS's get older, that cable will corrode and bind. Thanks again.
__________________
2006 LS430 CL Mercury Metallic / Black
- SmartAccess, 18" chrome wheels, sport sway bar, turn signal mirrors, VaisTech MML, console storage box
2001 LS430 ML / Nav Millenium Silver Metallic / Gray
- 17" hyper silver wheels, VaisTech MML, upgraded Nav to Gen 4

1995 LS400 - sold
1990 LS400 - sold
Tom57 is offline   Reply With Quote
Old 04-05-14, 06:01 PM   #5
kokkinias
Driver School Candidate
Trader Score: (0)
 
Join Date: Mar 2014
Location: IL
Posts: 2
Default

Need to unbolt the fuse box in upper right hand corner to get to the black boot. Use that hanger to push thru the firewall. Attach the cable and feed inside.

Last edited by kokkinias; 04-05-14 at 10:11 PM..
kokkinias is offline   Reply With Quote
Old 04-05-14, 06:01 PM
 
 
 
 
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
DIY hood latch cable replacement lexsc3 GS - Second Generation 59 06-05-14 08:45 AM
Don't do what I did while fixing power doorlocks! Bon LX470 and LX450 0 02-11-13 09:30 PM
DIY: Subwoofer install without drilling anything rojo412 LS400 11 03-08-10 08:31 PM
Chrome Door Handles DIY G2SSM RX - Second Generation 17 09-29-08 07:45 AM
Hood Release Cable Adjustment edbro RX - First Generation 2 04-02-07 05:50 PM


Tags
02, 430, black, cable, diy, hood, latch, lexus, ls, ls430, release, replace

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump

All times are GMT -7. The time now is 01:53 AM.

Join ClubLexus
Advertising


Copyright © 2000-2008 Internet Brands, Inc. All Rights Reserved
Privacy Policy | Disclaimer | Terms of Use | JOBS


Get all contact info