Go Back   Club Lexus Forums > Lexus Model Forums > LS Models > LS430
Sign in using an external account
Register Forgot Password?

DLC3 diagram. Zero point calibration.

Reply
 
 
 
 
Thread Tools Search this Thread Display Modes
Old 01-28-11, 12:13 PM   #1
alpop
Driver School Candidate
Trader Score: (0)
 
Join Date: Jun 2010
Location: ca
Posts: 6
Default DLC3 diagram. Zero point calibration.

After my mechanic changed my brake pads and the break wear sensor, he reseted the memory (by mistake) and now I'm getting the "Check VSC" warning. From what I've read, I need to do a Zero point calibration and I found something online that doesn't require any special tool but only a jump wire. For that I need to jump two pins in DLC3, which are TS and CG, and I got differrent opinions about their location in DLC3. So I'm looking to find a DLC3 diagram for 2003 LS 430, if anyone can help. Here is the instructions I found for the zero point calibration; any comments about this are appreciated.

******************************************************

Zero Point Calibration Using SST 09843–18040
The following procedure may be used in the cases where a Diagnostic Tester is
not available.
NOTE:
While performing the Zero Point Calibration, do not tilt, move or shake the vehicle.
The vehicle must remain in a stationary condition throughout the entire process.
Be sure to perform the procedure on a level surface with an inclination of less than 1%.
1. Ensure the shift lever is in the “P” range.
2. Turn the ignition switch ON.
3. Using SST 09843–18040, repeat a cycle of short and open between terminals Ts and
CG of DLC3 4 times or more within 8 seconds (refer to the specific vehicle EWD for
TS and CG pin location in the DLC3).
4. Verify that the VSC indicator light is lit indicating the recorded zero point is erased.
5. Turn the ignition switch OFF.
6. Be sure the terminals Ts and CG of DLC3 are disconnected.
7. Turn the ignition switch ON.
8. Check that the VSC warning light goes off about 15 seconds after the ignition switch
is turned ON.
9. After ensuring that the VSC warning light remains OFF for 2 seconds, turn the ignition
switch OFF.
10. Connect terminals Ts and CG of DLC3 using SST 09843–18040.
11. Turn the ignition switch ON.
12. After turning the ignition switch ON, check that the VSC warning light is lit for about
4 seconds and then starts quick blinking at 0.13 second intervals.
13. After ensuring the blinking of the VSC warning light for 2 seconds, turn the ignition
switch OFF.
14. Remove the SST from terminals Ts and CG of DLC3.
15. Drive the vehicle for at least 5 minutes to confirm Zero Point Calibration is complete.
NOTE:
If viewing Diagnostic Tester Data List after repair, the Steering Angle Sensor may
remain at 1150 until the vehicle reaches 28 mph. This is a normal condition until the
learned values of the steering angle have been achieved.
Calibration
Procedure
With SST

*********************************************
The SST 09843–18040 is ...the jump wire, any piece of wire you may find.
Here are two links with TS and CG in different positions:
http://forum.ih8mud.com/200-series-c...-g-sensor.html
http://www.clublexus.com/forums/ls43...c-vsc-off.html
Thank you very much.
alex
This ad is not displayed to registered members.
Register your free account today and become a member on Club Lexus!

Last edited by alpop; 01-28-11 at 02:14 PM..
alpop is offline   Reply With Quote
Old 01-28-11, 03:22 PM   #2
jimbosr1
Lexus Test Driver
Trader Score: (0)
 
jimbosr1's Avatar
 
Join Date: Sep 2010
Location: ga
Posts: 848
Default

have the person fix it sence he made the mistake.
jimbosr1 is offline   Reply With Quote
Old 01-28-11, 04:54 PM   #3
alpop
Driver School Candidate
Trader Score: (0)
 
Join Date: Jun 2010
Location: ca
Posts: 6
Default I fixed it

I did it myself with the instructions on this forum and it worked. Thank you all. God bless you.
alex
alpop is offline   Reply With Quote
Old 02-21-13, 11:54 PM   #4
Armada
Driver School Candidate
Trader Score: (0)
 
Join Date: Jan 2013
Location: Tx
Posts: 1
Default

Thanks for this instruction, It worked like Charm
Armada is offline   Reply With Quote
Old 11-22-13, 05:37 PM   #5
russ1958
Driver School Candidate
Trader Score: (0)
 
Join Date: Jul 2011
Location: PA
Posts: 10
Default

Good evening Friends,
I had a wheel sensor replaced on my 1998 gs300, now I have the ABS VSC lights. Want to do the zero point calibration, can someone tell me where tthe TS and CG are. Are they 12 (TS) and 4(CG)?
russ1958 is offline   Reply With Quote
Old 11-22-13, 05:41 PM   #6
Lynzoid
Lead Lap
Trader Score: (0)
 
Join Date: Jun 2010
Location: RU
Posts: 722
Default

wrong forum man
Lynzoid is offline   Reply With Quote
Old 11-22-13, 05:41 PM
 
 
 
 
Reply

Tags
2003, calibration, diagram, dlc3, es, lexus, ls430, missing, pin, point, sc430, sst, suspension, ts, vsc

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
SCFAQ: Airbag Warning Light Reset O. L. T. SC 400/300 41 07-06-14 01:10 PM
Help with is250 and techstream knockoff, will it work? kentucky1 IS - Second Generation 2 02-16-14 04:39 PM
Vsc, Vsc off, and abs light on 2000 Gs300 franz420 GS - Second Generation 25 01-21-14 07:59 AM
VSC Brake Light Reset iGS430 GS - Third Generation 1 11-27-13 06:58 PM
Zero Point Calibration russ1958 GS - Second Generation 3 11-23-13 01:36 PM

All times are GMT -7. The time now is 01:23 AM.

Join ClubLexus
Advertising


Copyright © 2000-2008 Internet Brands, Inc. All Rights Reserved
Privacy Policy | Disclaimer | Terms of Use | JOBS


Get all contact info