LS - 1st and 2nd Gen (1990-2000) Discussion topics related to the 1990 - 2000 Lexus LS400

Hood release doesn't work.

Thread Tools
 
Search this Thread
 
Old 06-26-07, 10:35 AM
  #1  
GreenGrass
Driver School Candidate
Thread Starter
 
GreenGrass's Avatar
 
Join Date: Jul 2005
Location: AZ
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default Hood release doesn't work.

I get a dry pull from the hood release. The cable is attached inside the cabin but I have no resistance. Does anyone have any suggestions on how to get the hood open without the use of the cabin hood release? Help would be appreciated - I was all set to change my oil...glad I didn't drain it first!
Old 06-26-07, 10:59 AM
  #2  
absolut
Pole Position
 
absolut's Avatar
 
Join Date: Jul 2005
Location: FL
Posts: 269
Likes: 0
Received 0 Likes on 0 Posts
Default

try having someone pull up on the hood as you pull the hood release. Your hood shocks might be dead so your hood is not getting enough upward pressure to 'pop' open.
Old 06-26-07, 02:53 PM
  #3  
GreenGrass
Driver School Candidate
Thread Starter
 
GreenGrass's Avatar
 
Join Date: Jul 2005
Location: AZ
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default

I hooked a bungie cord to the release - pulled back as far as it would go - and tugged on the hood. It is still locked. It moves a few mm and hits metal (the latch). Thank you but no luck. Any other thoughts?
Old 06-26-07, 06:24 PM
  #4  
avalon42
Lexus Test Driver
iTrader: (1)
 
avalon42's Avatar
 
Join Date: Jan 2007
Location: California
Posts: 1,194
Likes: 0
Received 6 Likes on 6 Posts
Default

have you checked the cable? If the cable is pulling back considerably, I would suspect the actual latch mechanism itself has gone out.
Old 06-26-07, 07:41 PM
  #5  
808-lexus
Driver School Candidate
 
808-lexus's Avatar
 
Join Date: Jun 2007
Location: hawaii
Posts: 18
Likes: 0
Received 0 Likes on 0 Posts
Default

i have a similar problem.....my trunk doesn't open from the latch inside the car.
Old 06-26-07, 08:15 PM
  #6  
mobilyte
Pole Position
iTrader: (3)
 
mobilyte's Avatar
 
Join Date: Jul 2006
Location: IL
Posts: 299
Likes: 0
Received 2 Likes on 2 Posts
Default

the trunk switch is electronic, the hood release is mechanical.

for the hood, remove the lower dash panel where the hood release lever is located . there are 3 philips head screws, 1 set of wires for the small light on that panel, and the cable for the hood release. remove the cable from the hood release lever (attaches like a bicycle's brake/deraileur cable to handlebar lever), pull the cable with a pair of pliers while a helper pulls up on the hood. if that manages to work, you can loosen the 3 10mm bolts and adjust the height of the latch assembly on the core support (dont forget to adjust the small rubber stoppers at the edge of the hood to make the hood sit flush with the fenders).

if the hood still wont open, try to spray some lubricant through the grill insert onto the latch. worst case scenario would be to break the grill insert to gain access to the latch.
Old 06-26-07, 09:04 PM
  #7  
GreenGrass
Driver School Candidate
Thread Starter
 
GreenGrass's Avatar
 
Join Date: Jul 2005
Location: AZ
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default

I'm pretty sure the problem is with the latch at the grill. That cable goes all the way back without any tension whereas before it released at 1/4 to 1/3 of a tug. ANY thoughts on access via the grill? I'm not above breaking the grill if I knew I could open the hood afterward.
Old 06-27-07, 09:40 PM
  #8  
skperformance
Lexus Champion
iTrader: (6)
 
skperformance's Avatar
 
Join Date: Nov 2002
Location: Mississauga,Ontario,Canada
Posts: 3,488
Likes: 0
Received 8 Likes on 8 Posts
Default

Removing the panelling under the front bumper will also give you access to the lock.
Old 04-19-09, 07:18 PM
  #9  
Kremkauj
Driver School Candidate
 
Kremkauj's Avatar
 
Join Date: Mar 2007
Location: Georgia
Posts: 6
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by GreenGrass
I get a dry pull from the hood release. The cable is attached inside the cabin but I have no resistance. Does anyone have any suggestions on how to get the hood open without the use of the cabin hood release? Help would be appreciated - I was all set to change my oil...glad I didn't drain it first!
Did you have any sucess?! I have the same issue and would love to know if I should go through the trouble of figuring it out.

If that isn't bad enough, I found out I couldn't get in when I was trying to jump my wife's mini-van. Oh the irony.

Any input would be appreciated.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
i928
LS - 1st and 2nd Gen (1990-2000)
10
03-08-16 05:06 PM
SC3coupe
SC- 1st Gen (1992-2000)
4
08-14-13 07:43 AM
ExKoukiS14
IS - 2nd Gen (2006-2013)
16
02-14-12 11:00 AM
F4Luder
GS - 2nd Gen (1998-2005)
10
08-03-05 05:37 PM



Quick Reply: Hood release doesn't work.



All times are GMT -7. The time now is 01:39 PM.