Anyone know what to do to fix this
#1
3rd Gear
Thread Starter
Join Date: Apr 2023
Location: NM
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Anyone know what to do to fix this
Hello all I have a 2006 IS250 and recently it wouldn't go into gear at all I towed it home dropped the transmission pan changed the fluid and filter took out the solenoids cleaned them well put them back in a test drove it where it was shifting after high rpm then all the sudden it got stuck basically in drive reverse is drive and neutral is drive the only gear that is true is park so it sits again till I figure out what to do next ran the codes and it comes back with p0781 (1-2 shift malfunction) and p0761 (shift solenoid c stuck off) so I'm at a loss I keep researching and researching till my head is pounding so bad so any help with this would be more than amazing and appreciated the mileage on it is around 240k and it sat for a couple of years before I got it .
#2
Lexus Test Driver
iTrader: (2)
Hello all I have a 2006 IS250 and recently it wouldn't go into gear at all I towed it home dropped the transmission pan changed the fluid and filter took out the solenoids cleaned them well put them back in a test drove it where it was shifting after high rpm then all the sudden it got stuck basically in drive reverse is drive and neutral is drive the only gear that is true is park so it sits again till I figure out what to do next ran the codes and it comes back with p0781 (1-2 shift malfunction) and p0761 (shift solenoid c stuck off) so I'm at a loss I keep researching and researching till my head is pounding so bad so any help with this would be more than amazing and appreciated the mileage on it is around 240k and it sat for a couple of years before I got it .
My point is, there are other valves in the valve body, check *****, clutch packs, pistons and bands that need to apply clamp force, to the clutch material to select a gear. If the gear selected doesn't produce the correct result, the TCU throws a code pointing to the last action requested which was solenoid X being commanded to do a job.
What needs done is pressure testing the transmission case (remove valvebody) and using an air gun to see if responsible fluid channels act on the specified band or drum making it clamp or does it just make a big air leak?
Question, was the fluid burned and stinky? Was there a pile of rubble in the pan? Did you see it, do the work yourself?
#2IS Transmission Repair
Last edited by 2013FSport; 03-30-24 at 01:22 PM.
#3
3rd Gear
Thread Starter
Join Date: Apr 2023
Location: NM
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Yes the fluid was horrible it was super black I didn't see anything in it however it was very dark and I honestly don't recall too horrible of a smell I mean yah it smelt bad and burnt you can say and yes I do most of the work myself as I'm a single mom of three and don't trust many people so google, youtube and of course, this forum is what tremendously helps me get through most of it but I'm far from a professional I just do my best. I am trying to understand fully now what you said I mean I understand but I'm not quite sure how to do that stuff yet I do greatly appreciate your feedback
#4
Lexus Test Driver
iTrader: (2)
Yes the fluid was horrible it was super black I didn't see anything in it however it was very dark and I honestly don't recall too horrible of a smell I mean yah it smelt bad and burnt you can say and yes I do most of the work myself as I'm a single mom of three and don't trust many people so google, youtube and of course, this forum is what tremendously helps me get through most of it but I'm far from a professional I just do my best. I am trying to understand fully now what you said I mean I understand but I'm not quite sure how to do that stuff yet I do greatly appreciate your feedback
Did it have a leak and ran low on fluid?
Here is a diagram of the A760E RWD to give you some insight about what all is going on inside. Let me know if there is anything I can answer for you and best of luck.
https://at-manuals.com/wp-content/up...960-scheme.jpg
#6
Lexus Test Driver
iTrader: (2)
That is correct. As stated, others here have used up to a 2015 A960E so that gives you options as there plenty of used low mileage units out there.
Yes, there are mom and pop shops out there that can successfully R&R a trans. Do search on here, a member did a writeup DIY replacement with quality pictures and text. It could help you ask better questions about what you are paying for or allow you to DIY.
If you had the car up and dropped the pan, you are in a good spot to do this yourself. It really is just nuts and bolts, being sensible and don't put yourself at risk with cinder blocks and crap like that.
I used to work at transmission shop doing R&R and rebuilds. Ask any questions you have, I'll try and help.
GL
The following users liked this post:
Protholl (04-03-24)
Thread
Thread Starter
Forum
Replies
Last Post