specie

iTrader: (1)

Wheels: 19x9.5/10.5 +35
Vehicle: '06 IS350; fenders are rolled, front bumper tabs are shaved, lowered about half finger gap front and back.

Was thinking 245/35 fronts and 265/35-275/30 for the rears. Would these have any rubbing issues with the wheel specs listed?

laobo979

iTrader: (5)

245-35 up front most I'd go is 235-35 and rear you might get away with 265-30 with a little of camber adjustment.

laobo979

iTrader: (5)

Anything can tuck if you do the work. Which shouldn't be much.

ahli08

What about the 18 inches Te37 8.5j with 30 offset? will the fenders be flushed? Any rubbing issues?

xHyphen

08 IS350:
F: 18x9.5 +25 215/35
R: 18x11.5 +20 265/40

Can or no can?

WylieKylie

iTrader: (2)

^ Personally I think your sizes are messed up. Your front is a bit narrower and more than one inch smaller diamater than a stock 18" tire and you are stretching it onto a wheel that is 1.5" wider. You may even have a problem finding a tire shop willing to stretch that on the rim for you. At a minimum I would go with a 235/40 on the front. Personally I'd put it on a 8.5-9" rim, but a 9.5" would be ok.

The rear tire size is better, but again I see no reason to stretch a 265 onto such a wide wheel, and you may have trouble finding a shop to do that for you. I'd stick with that same size tire and move to a 9.5 to 10.5" wheel.

*DISCLAIMER: I think stretch/poke/hellaflush fitments are nonsense.

pmanliu

iTrader: (4)

What size spacer should i run in the rear for flush fitment? Currentl its 18x8.5, +35 (225/40/18)

I'm thinking +15 but wasn't sure if i'd need to roll...

RVCAis250

Would you be willing to roll or do you want to avoid that?

Also, how low are you?

RVCAis250

You don't need that much stretch in the front. You'd be fine with a 225/35..
In the rear, I'd personally go with 265/35, so you almost got it right, but even with that, those are really aggressive specs in the rear. For that, you'd need a roll and pull and relocate fender tabs. It could work but it'll take some time and hacking at the fenders.

pmanliu

iTrader: (4)

I'm currently on tein s-tech's and would want to avoid rolling

Doriimon

19x9.5 +25 with 265/35s going to work on the rear with rolled guards? Lowered on S techs

RVCAis250

You're about right then, a +15mm will work good. You could even do a +20mm and that would still work but idk if they make that specific spacer size. A +25mm would be cutting it close but with springs you could probably get away with it. But if your just going for flush fitment (no poke) I'd just do the 15/20mm

CCJ22

iTrader: (26)

Will 19x9.5 +40 front wheel hit any suspension components?

I know I can run 19x9.5+35 all day. Not sure about +40 though.

ldc

Hi guys, this has just come to mind.

With our stock offset 45+, will putting a lower offsett wheel on require longer studs?

zmcgovern4

iTrader: (2)

Local guy is selling these concept one cs10's... love the wheels, but not so sure on if they would fit my 2IS.



Specs are:
Front - 20x9.5+25
Rear - 20x10.5+27

I'm currently lowered about 1.75" on Megan EZ's and have no fender mods, but am willing to do a fender roll and maybe a slight pull.

Any advice on fitment and suggested tire specs would be appreciated.

Thanks