Most nitrous stock motor can take?
#16
Pole Position
iTrader: (1)
I would say MotorSport 109 or VP Import. Call VP racing fuels for better information. 210-635-7744
As far as removing the primary cats you will have to run o2 simulators on the secondary o2 sensors or you will throw a CEL code, I believe. I believe that PPE and Sikky make them.
As far as removing the primary cats you will have to run o2 simulators on the secondary o2 sensors or you will throw a CEL code, I believe. I believe that PPE and Sikky make them.
#17
Driver
Thread Starter
Join Date: Jan 2013
Location: NC, Formerly CA
Posts: 164
Likes: 0
Received 0 Likes
on
0 Posts
I would say MotorSport 109 or VP Import. Call VP racing fuels for better information. 210-635-7744
As far as removing the primary cats you will have to run o2 simulators on the secondary o2 sensors or you will throw a CEL code, I believe. I believe that PPE and Sikky make them.
As far as removing the primary cats you will have to run o2 simulators on the secondary o2 sensors or you will throw a CEL code, I believe. I believe that PPE and Sikky make them.
#18
Lexus Champion
Join Date: Jun 2007
Location: Aventura, Florida
Posts: 2,148
Likes: 0
Received 0 Likes
on
0 Posts
So All in all you think I could go up to 175 with a standalone cell, and gutted/deleted cats? I am planning on running a degree or 2 colder plugs as well to keep it safe. Would you suggest considering getting better rods to go up a bit, or at that point should I just reconsider revamping the whole motor?
Also, I have seen a lot of your project with the 2ur motor, what are you doing for an ecu in the high hp motor?
Also, I have seen a lot of your project with the 2ur motor, what are you doing for an ecu in the high hp motor?
With my big power motor, ive been torn between the AEM infinity and Motec. Life has been coming at me fast ( GF moving in, mom asking for kids , etc lol ) so ive been kinda side tracked from the project
I understand the tuning issue. I was just merely stating that you can mix the fuels. It was stated above that it would not be a good idea, ive been doing it for years. thats it. the timing and compression issue i completly understand, i was just stating the cats and o2 sensors would be hating life when you run C16 LEADED fuel thru them. there are perfectly good UNLEADED race fuels that would work and the o2 sensors and cats would be happy.
#19
Driver
Thread Starter
Join Date: Jan 2013
Location: NC, Formerly CA
Posts: 164
Likes: 0
Received 0 Likes
on
0 Posts
Lack of flow with the sikky headers caused the "record" car the detonate in cylinder #1. Its not my car so I wont go into detail as to the extent of damage that the detonation caused, but ill say that its not something you'll want to go through. I personally killed a few number 1 plugs on a 150 shot in cylinder #1 due to the sikky headers before my engine builder saw the set for the first time.
I would say that the car should be perfectly fine at 175 with the setup you have in mind. From what we have seen when my motor was apart, the stock engine is amazingly well designed and fortified. With a proper header, I believe that the stock motor could easily make 800-900hp with a turbo.
With my big power motor, ive been torn between the AEM infinity and Motec. Life has been coming at me fast ( GF moving in, mom asking for kids , etc lol ) so ive been kinda side tracked from the project
All the info from your posts are good.
I would say that the car should be perfectly fine at 175 with the setup you have in mind. From what we have seen when my motor was apart, the stock engine is amazingly well designed and fortified. With a proper header, I believe that the stock motor could easily make 800-900hp with a turbo.
With my big power motor, ive been torn between the AEM infinity and Motec. Life has been coming at me fast ( GF moving in, mom asking for kids , etc lol ) so ive been kinda side tracked from the project
All the info from your posts are good.
#20
Driver
Thread Starter
Join Date: Jan 2013
Location: NC, Formerly CA
Posts: 164
Likes: 0
Received 0 Likes
on
0 Posts
#21
The nitrous motor that detonated in cyclinder 1, is that due to headers design or maybe due to cyclinder 1 getting more nitrous? Is it a direct port setup or just from 1 nozzle?
#23
My plan or strategy on my car is not go over the 100 shot! Ive seen this cars when the owner or programer try to push more than 125 shot the ecu feels the NOS presence and starts to rich the mixture and the car struggles big time , lots of NOS on this engine will cause a detonation very dangerous where our hollow cams will let go , then you have a blown engine
Last edited by KOKISF; 08-08-14 at 09:10 AM.
#24
Lack of flow with the sikky headers caused the "record" car the detonate in cylinder #1. Its not my car so I wont go into detail as to the extent of damage that the detonation caused, but ill say that its not something you'll want to go through. I personally killed a few number 1 plugs on a 150 shot in cylinder #1 due to the sikky headers before my engine builder saw the set for the first time.
I would say that the car should be perfectly fine at 175 with the setup you have in mind. From what we have seen when my motor was apart, the stock engine is amazingly well designed and fortified. With a proper header, I believe that the stock motor could easily make 800-900hp with a turbo.
With my big power motor, ive been torn between the AEM infinity and Motec. Life has been coming at me fast ( GF moving in, mom asking for kids , etc lol ) so ive been kinda side tracked from the project
All the info from your posts are good.
I would say that the car should be perfectly fine at 175 with the setup you have in mind. From what we have seen when my motor was apart, the stock engine is amazingly well designed and fortified. With a proper header, I believe that the stock motor could easily make 800-900hp with a turbo.
With my big power motor, ive been torn between the AEM infinity and Motec. Life has been coming at me fast ( GF moving in, mom asking for kids , etc lol ) so ive been kinda side tracked from the project
All the info from your posts are good.
Thread
Thread Starter
Forum
Replies
Last Post