PPE header & CEL
#18
Pole Position
iTrader: (2)
This has been happening to my F also. Ive had the PPE headers in for about a year now with no CEL or problems til now. The car has been sitting basically all winter, started every few weeks. First chance I got to drive it, after 30 min the CEL came on, on the drive (approx. 3 miles) the CEL went away. Few weeks after that same thing, after another short 3-5 mile drive it disappeared and reappeared again. Limp mode each time. When I installed the ppe I put in brand new A/F sensors, is it possible to go bad after 1 yr? maybe its the old gas?
#23
Tech Info Resource
iTrader: (2)
Anything sensor 1 (bank 1 or 2, doesn't matter) is not related to the O2 sim at all. Sensor 1 on both sides is the wideband sensor.
I'd be checking for mechanical damage to the sensor, or a wiring problem, like the wire touching something hot and getting the insulation melted. Was it install with the right tools to the right torque setting? Over torque will damage the sensor the same as a sparkplug.
Originally Posted by TIS
Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
• Air fuel ratio sensor (bank 1, 2 sensor 1)
• ECM
• Air fuel ratio sensor (bank 1, 2 sensor 1)
• ECM
#24
It was fine for a 1 1/2 years. I replaced it with the original one (on the old headers) and it still gave me the code. Next test is to swap right and left so see if I still get Bank 2 vs. Bank 1.
#25
Lead Lap
iTrader: (13)
Mines just came on this morning and like the op describe it was raining yesterday. Only thing I can think of was that I drove over a puddle of water and after that it was acting funny and went to limp mode. I will check back once I get off of work and scan my car for the codes to see what is coming up. Hopefully it goes away, crossing my fingers.
#26
This has happened 5 times in last 2yrs since installing my PPE twice during summer months first year and same thing second year and once this past Dec, I've changed O2 and AF sensors but still having issue. Each time I cleared it with my scan tool and would go for nearly year before issue popping up again. When it happens again I'll order new O2 Conditioner from PPE.
#27
Rookie
Thread Starter
Join Date: Apr 2013
Location: AB
Posts: 70
Likes: 0
Received 0 Likes
on
0 Posts
Mines just came on this morning and like the op describe it was raining yesterday. Only thing I can think of was that I drove over a puddle of water and after that it was acting funny and went to limp mode. I will check back once I get off of work and scan my car for the codes to see what is coming up. Hopefully it goes away, crossing my fingers.
#28
Tech Info Resource
iTrader: (2)
The connectors and the device itself need to be protected from water. If water gets in the sensor, it will not work. If water gets in the connector(s) it will fail too.
#30
Tech Info Resource
iTrader: (2)
There is normally a red rubber (nitrile) gasket in the connector to keep water out. I would inspect the connector and make sure this gasket is in place and sealing correctly. If it is not, either order a new connector from Lexus (90980-10869) for the harness end or if you want to try going cheap, get some connector grease and put in in the connection. Ford used to have some stuff for their , and way back in the early days of motorcycle engine management, the Japanese companies uses this as well.
Alternates for the connectors (if you know exactly what you are looking for) are http://www.newunitedracetech.com/shop/.
It looks like a Yazaki connector - http://connectors-catalog.sys.yzk.co...list&select=15
The sensor end appears to be http://connectors-catalog.sys.yzk.co...tail&select=15
Might also be Sumitomo - http://easternbeaver.com/Main/Elec__...SMSL/smsl.html Look at the 4P connector...
Alternates for the connectors (if you know exactly what you are looking for) are http://www.newunitedracetech.com/shop/.
It looks like a Yazaki connector - http://connectors-catalog.sys.yzk.co...list&select=15
The sensor end appears to be http://connectors-catalog.sys.yzk.co...tail&select=15
Might also be Sumitomo - http://easternbeaver.com/Main/Elec__...SMSL/smsl.html Look at the 4P connector...
Last edited by lobuxracer; 03-20-14 at 12:26 PM.