What a nice set of wheels with a lip...IS350
#1
Rookie
Thread Starter
Join Date: Feb 2016
Location: Texas
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
What a nice set of wheels with a lip...IS350
Am sure this has been brought up but,,, am looking for a set of wheels with a nice lip for my 2006 IS350. Prefer 18 inch, most manufactured can't make it for the IS350 cause it wont clear the front brake caliper and i dont want to use spacers. Any suggestions?
If i had IS250, wheels all day long. lol
Thanks
If i had IS250, wheels all day long. lol
Thanks
#2
Instructor
get something with lower offset... or check out the wheel thread in the sticky... my wheels had that problem aswell where my rear have lip but front don't... but mine actually don't look too bad because my rear wheel's lip is not that deep dish so it kinda worked out...
#3
Rookie
Thread Starter
Join Date: Feb 2016
Location: Texas
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
get something with lower offset... or check out the wheel thread in the sticky... my wheels had that problem aswell where my rear have lip but front don't... but mine actually don't look too bad because my rear wheel's lip is not that deep dish so it kinda worked out...
Problem with low offset will make the wheel stick out in the front. I like it flush not poke so it really hard to find wheels with lip for IS350 for a reasonable price.
#4
Instructor
this is mine... front wheel have like no lip and rear does...
Trending Topics
#9
Rookie
Thread Starter
Join Date: Feb 2016
Location: Texas
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
Am no so sure then since its not your car that its a 350. To have a front lip that deep its hard to clear the brakes. I seen guys use 7mm spacers and end up poking wheel out or not safe to drive with short wheels studs. Any bigger spacer will not work unless you want major poke
#10
Pole Position
iTrader: (5)
Am no so sure then since its not your car that its a 350. To have a front lip that deep its hard to clear the brakes. I seen guys use 7mm spacers and end up poking wheel out or not safe to drive with short wheels studs. Any bigger spacer will not work unless you want major poke
I noe a couple ppl with 3is and they run these rims with no spacers.
#11
Rookie
Thread Starter
Join Date: Feb 2016
Location: Texas
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the feedback.
#12
The Work VS-XX can have a nice amount of lip and still clear the brakes. It all depends on the type of disk you choose for the front.
The following are the different type of disks that Work offer for their 3 piece wheels.
A disk - Standard dish
O disk - Deep dish
R disk - Big caliper dish
T disk - Big caliper dish
The following are the different type of disks that Work offer for their 3 piece wheels.
A disk - Standard dish
O disk - Deep dish
R disk - Big caliper dish
T disk - Big caliper dish
#14
Rookie
Thread Starter
Join Date: Feb 2016
Location: Texas
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
#15
Pole Position
iTrader: (5)
Am no so sure then since its not your car that its a 350. To have a front lip that deep its hard to clear the brakes. I seen guys use 7mm spacers and end up poking wheel out or not safe to drive with short wheels studs. Any bigger spacer will not work unless you want major poke
Check out their spec to see if it would work for u. You would prolly need to roll fenders.
http://www.mppsociety.com/project/jaydangys-lexus-is350/