AGGRESSIVE ISX50 wheel thread
12-04-15, 12:53 PM
#2086
Driver School Candidate
iTrader: (1)
Join Date: Jun 2007
Location: CA
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
what you think I should run.....
19x8.5 +30 with a 19x10.5 +22
Or
19x9.5+35 with a 19x10.5 +22
Or
19x8.5+22 with a 19x9.5+22
I do not want to do any pulling just want a clean flush look.,.......
19x8.5 +30 with a 19x10.5 +22
Or
19x9.5+35 with a 19x10.5 +22
Or
19x8.5+22 with a 19x9.5+22
I do not want to do any pulling just want a clean flush look.,.......
01-13-16, 07:12 PM
#2087
I just recently switched to air suspension and been trying to get my fitment right. When the car is aired out, the rear toe goes in, making the corners of my rear bumper grind on the lips of my rims. I tried explaining this to the alignment shop but they just set my toe to factory specs, which made the issue worse. Now I can't tuck like in the picture without taking chunks out of my rims.
I have megan toe arms and spc camber arms. Fenders rolled and pulled. Wheels specs are:
Front: 19 x 9.5 +15
Rear: 19 x 11 +12
Any pointers would be greatly appreciated, as long as I get to keep my wheels :P
01-13-16, 07:14 PM
#2088
Good look can't wait to get my work rezax l installed
bagged cuz im not cool enough to be static
04-18-16, 10:18 AM
#2096
Driver
Join Date: Nov 2013
Location: NY
Posts: 138
Likes: 0
Received 0 Likes
on
0 Posts
18×10.5 square
He guys I want to run 18x10.5+35 square on my 2is AWD have anyone done that and what tires size did yah go with i was thinking 235/35/18 .....thanks and I will role fenders
04-20-16, 08:52 PM
#2097
Driver School Candidate
Join Date: Apr 2016
Location: California
Posts: 27
Likes: 0
Received 0 Likes
on
0 Posts
Im looking at 19x8.5 in the front and 19x9.5 in rear....both offset at +25.
If my car very low (nothing extreme but low enough to no wheel gap) will the setting i mentioned above suffice?
As well will i have a lot of negative camber with that setup?? I am trying to avoid negative camber as much as possible....
If my car very low (nothing extreme but low enough to no wheel gap) will the setting i mentioned above suffice?
As well will i have a lot of negative camber with that setup?? I am trying to avoid negative camber as much as possible....
04-22-16, 07:03 PM
#2100
Driver School Candidate
Join Date: Apr 2016
Location: California
Posts: 27
Likes: 0
Received 0 Likes
on
0 Posts
hey all,
I am looking at 19 x 8.5 in the front and 19 x 9.5 in the rear for my 2010 IS250 RWD......
what offset would you suggest if I plan on lowering the car to no wheel gap (flush with fender), and minimal camber?
I do not plan on going extremely low, but low enough to have slight tuck.
A friend suggested +25 offset......is that too much poke?
I am looking at 19 x 8.5 in the front and 19 x 9.5 in the rear for my 2010 IS250 RWD......
what offset would you suggest if I plan on lowering the car to no wheel gap (flush with fender), and minimal camber?
I do not plan on going extremely low, but low enough to have slight tuck.
A friend suggested +25 offset......is that too much poke?