What did you do to your GS today?
06-04-16, 01:46 PM
#1398
06-05-16, 12:03 PM
#1400
Pole Position
Clear sidemarkers installed.
Consequently, **** those 4 nuts to take off the front bumper cover. Why take off the front cover to install the side markers, you ask?
The rear nuts were so rusted I had to break then off, taking the bolt with them. I could not get enough torque from inside.
Consequently, **** those 4 nuts to take off the front bumper cover. Why take off the front cover to install the side markers, you ask?
The rear nuts were so rusted I had to break then off, taking the bolt with them. I could not get enough torque from inside.
Glad you got them off.
06-05-16, 04:07 PM
#1402
Originally Posted by dreamcar88
wow im getting mine this week hope i dont have same problem. Someone said u can take the fog lights out and get to the side markers alot easier
06-05-16, 04:32 PM
#1403
Originally Posted by dreamcar88
wow im getting mine this week hope i dont have same problem. Someone said u can take the fog lights out and get to the side markers alot easier
06-05-16, 05:30 PM
#1404
Fellas at Fender Defender rolled my fenders.
They were already shaved but had rubbing issues.
Preparing to switch up from current 18x8.5 et5 18x9.5 et0 to square set of 19x10 et25 and 10 rear -hopefully the roll will allow me to run 235/35 on all four corners. Won't know until wheels are back from refinishing. Front fitment is about the same within a mm actually so should be good!
They were already shaved but had rubbing issues.
Preparing to switch up from current 18x8.5 et5 18x9.5 et0 to square set of 19x10 et25 and 10 rear -hopefully the roll will allow me to run 235/35 on all four corners. Won't know until wheels are back from refinishing. Front fitment is about the same within a mm actually so should be good!
06-05-16, 05:30 PM
#1405
What I did was, I rotate the wheel inward on each side of the car, of course. LOL... Then I will remove all the screws on the front of the fender cover, them I pull the cover a little bit to one side and having more space in that area, so I could get them more easily without removing the bumper and once the installation of the new clear ones, was very easier. You can try that too.
06-05-16, 08:30 PM
#1406
AFA the bumper cover is concerned, I think my problem was I did not have a long enough socket extension. Getting to the top nuts was a pain. I also lost one.
06-05-16, 09:21 PM
#1407
Originally Posted by AmanO
Getting at then is not the issue.
AFA the bumper cover is concerned, I think my problem was I did not have a long enough socket extension. Getting to the top nuts was a pain. I also lost one.
AFA the bumper cover is concerned, I think my problem was I did not have a long enough socket extension. Getting to the top nuts was a pain. I also lost one.
06-06-16, 04:58 AM
#1408
Fellas at Fender Defender rolled my fenders.
They were already shaved but had rubbing issues.
Preparing to switch up from current 18x8.5 et5 18x9.5 et0 to square set of 19x10 et25 and 10 rear -hopefully the roll will allow me to run 235/35 on all four corners. Won't know until wheels are back from refinishing. Front fitment is about the same within a mm actually so should be good!
They were already shaved but had rubbing issues.
Preparing to switch up from current 18x8.5 et5 18x9.5 et0 to square set of 19x10 et25 and 10 rear -hopefully the roll will allow me to run 235/35 on all four corners. Won't know until wheels are back from refinishing. Front fitment is about the same within a mm actually so should be good!
Check it out
https://www.clublexus.com/forums/bui...per-build.html
Last edited by ericherm1; 06-06-16 at 05:02 AM.
06-06-16, 11:02 AM
#1409
I just fell in love with her all over again. Installed my new wheels over the weekend. I'm loving the beefy tire set up now. Specs are 18x10.5 +15 255/35/18 upfront and 19x11 +15 275/35/19 in the rear
Hope you guys like
Hope you guys like
The following users liked this post:
DarthBacon (02-20-19)
