FL COMPLETE AirLift Manual/Analog Management Package
#1
COMPLETE AirLift Manual/Analog Management Package
For now, I'm going to try selling this all as a full bundle, because I just want to get rid of all this extra stuff I have lying around.
As far as a short description goes, this is a complete manual management setup. Everything you would need to install air suspension on your car, with the exception of the air bags (and struts), air line, and a fitting, or two. Keep in mind that this setup primarily uses 1/4" air line.
Keep in mind that some of this stuff isn't exactly tightened down/mounted (see: gauges) because I didn't end up using it in my air setup. Also, please excuse my terrible pictures, as it's late, and my room is a mess.
Location: FL 34291
Willing to Ship: Yes, and I'm willing to ship US48. If you're in Hawaii, then it will cost extra.
Price: SOLD SOLD SOLD
I can also sell the system without the air compressor for $375 + Shipping and Paypal fees.
Contact Info: I communicate primarily via forum PMs, but I will give you my cell phone number at your request.
So first off, what's included?
As far as a short description goes, this is a complete manual management setup. Everything you would need to install air suspension on your car, with the exception of the air bags (and struts), air line, and a fitting, or two. Keep in mind that this setup primarily uses 1/4" air line.
Keep in mind that some of this stuff isn't exactly tightened down/mounted (see: gauges) because I didn't end up using it in my air setup. Also, please excuse my terrible pictures, as it's late, and my room is a mess.
Location: FL 34291
Willing to Ship: Yes, and I'm willing to ship US48. If you're in Hawaii, then it will cost extra.
Price: SOLD SOLD SOLD
I can also sell the system without the air compressor for $375 + Shipping and Paypal fees.
Contact Info: I communicate primarily via forum PMs, but I will give you my cell phone number at your request.
So first off, what's included?
- 1x Viair 380C air compressor (small size, and can do 200psi. Also has an NPT fitting for the leader hose, so you are able to remove the leader hose, and adapt it to use hardlines, should your build take that route.)
- 1x AirLift 5 gallon "chubby" air tank (6x 1/2" - 1x 1/4" ports, with fittings preinstalled, except for the compressor inlet)
- 4x AirLift 1/4" Paddle Valves (lines/fittings preinstalled)
- Single DIN paddle valve bezel (fits over/behind a single DIN slot)
- 2x AVS dual needle gauges (52mm diameter, and rated up to 160 psi. Comes with 1/8" Female NPT to 1/4" PTC connectors preinstalled)
- 1x AVS single needle gauge (52mm diameter, and rated up to 200 psi. Comes with 1/8" Female NPT to 1/4" PTC connector preinstalled)
- Bezel for 3 52mm gauges (Also has a small HornBlasters switch for the purpose of compressor turn on/off)
- Assorted PTC fittings (1/4" Y fittings, 1/4" T fittings, 1/4" elbow fittings, the list goes on)
- Assorted NPT fittings (I have all sorts of 1/2", 3/8", 1/4" brass fittings that I've accumulated from shipping mishaps and stuff left over that I didn't end up using due to change[s] of plans)
- 200psi HornBlasters pressure switch
- 1/4" Male NPT Quick Connect Coupler
- 5-port 1/4" manifold
- My personal support
- And much, much more!
Last edited by Sc0pe; 11-29-14 at 04:23 PM.
#4
Pole Position
iTrader: (1)
Join Date: May 2014
Location: Orlando, Florida
Posts: 243
Likes: 0
Received 0 Likes
on
0 Posts
Hey Scope, I'm not really a buyer right now because of maintenance prices I just went through/still going through, but if you were to lets say want to use this in an sc400, would you need anything else other than lines, struts/bags?
Sorry for a bump with just a question lol but I'm curious. Because it seems like a good deal if you can source some bags/struts for a fair price. Glws, thanks
Sorry for a bump with just a question lol but I'm curious. Because it seems like a good deal if you can source some bags/struts for a fair price. Glws, thanks
#5
Hey Scope, I'm not really a buyer right now because of maintenance prices I just went through/still going through, but if you were to lets say want to use this in an sc400, would you need anything else other than lines, struts/bags?
Sorry for a bump with just a question lol but I'm curious. Because it seems like a good deal if you can source some bags/struts for a fair price. Glws, thanks
Sorry for a bump with just a question lol but I'm curious. Because it seems like a good deal if you can source some bags/struts for a fair price. Glws, thanks
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
frshhhhh
General Classifieds
0
06-07-17 07:46 PM
donnieb83
General Classifieds
6
12-04-13 05:46 PM
kelzzz
2Gen IS250 / IS350 / IS-F Classifieds (06-13)
32
07-17-12 06:31 AM