FL parts leftover after my supra was stolen
#1
Driver School Candidate
Thread Starter
Join Date: Jan 2011
Location: fl
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
parts leftover after my supra was stolen
This post is mostly copied and pasted from supraforums:
mk3 supra lightly used 1 piece light weight d.s. $275 shipped (it was custom made by a drive shaft shop, used, then sold to me), I test fit it but didn't use it (there was a vibration that i though was the oe d.s. but it wasn't broken so i put the oe d.s. back).
brand new transmission mount for r154 from dealer $35 shipped
brand new engine mount (dealer) for 2j works on 7m and 1j (search how) $55 shipped
6 heat shrink wrapped coil packs: worked fine on a 62mm turbo at 20 psi SOLD
1jz full gasket set (dealer) minus valve cover and intake manifold gaskets $50 shipped
2jz USA cams $85 shipped can be machined (for $125) good for 20-40 horsepower depending on setup.
mk3 oem dark gray ash tray $20 shipped.
some old 17x8 17x9 rims $150 local pickup
r154/v160 jz clutch setup six puck (this is a six speed pressure plate (lightly used southbend), light weight fidanza flywheel (new friction surface i.e. steel ring), and a kevlar disk that matches the spline of the r154). for some reason the supra community doesn't use this setup, while the lexus community has been doing it for years. search the lexus forums and you will find the necessary info. comes with everything needed for the install (including bearing, snap rings, and washer brand new from dealer (pics on request)). the pressure plate was painted to prevent surface rust.
$550
also shell for sale : http://www.supraforums.com/forum/sho...nd-aftermarket
I have pmed user drewgo and he will vouch for me thanks
mk3 supra lightly used 1 piece light weight d.s. $275 shipped (it was custom made by a drive shaft shop, used, then sold to me), I test fit it but didn't use it (there was a vibration that i though was the oe d.s. but it wasn't broken so i put the oe d.s. back).
brand new transmission mount for r154 from dealer $35 shipped
brand new engine mount (dealer) for 2j works on 7m and 1j (search how) $55 shipped
6 heat shrink wrapped coil packs: worked fine on a 62mm turbo at 20 psi SOLD
1jz full gasket set (dealer) minus valve cover and intake manifold gaskets $50 shipped
2jz USA cams $85 shipped can be machined (for $125) good for 20-40 horsepower depending on setup.
mk3 oem dark gray ash tray $20 shipped.
some old 17x8 17x9 rims $150 local pickup
r154/v160 jz clutch setup six puck (this is a six speed pressure plate (lightly used southbend), light weight fidanza flywheel (new friction surface i.e. steel ring), and a kevlar disk that matches the spline of the r154). for some reason the supra community doesn't use this setup, while the lexus community has been doing it for years. search the lexus forums and you will find the necessary info. comes with everything needed for the install (including bearing, snap rings, and washer brand new from dealer (pics on request)). the pressure plate was painted to prevent surface rust.
$550
also shell for sale : http://www.supraforums.com/forum/sho...nd-aftermarket
I have pmed user drewgo and he will vouch for me thanks
Thread
Thread Starter
Forum
Replies
Last Post
Li Ls4
SC400 / 300 Classifieds
15
09-19-12 04:19 PM