Halon

iTrader: (6)

I guess it makes sense, since we're using a 'short shifter'. It'd be great if the fulcrum was more similar to a normal shifter.

LoveSCs

iTrader: (2)

Excellent work on that piece!

You will get used to it, trust me. You will mis shift in the beginning, but then you get used to where the gears are. As long as you're not banging gears all of the time, you will be fine.

Ali SC3

iTrader: (10)

maybe if you start with a real 240sx shifter, it might be better? never thought of that before lol

Halon

iTrader: (6)

Under that black cover, there is a spring and ball. Are there actually 2 sorings? I took my cover off, there's a big spring in there that is sticking out. But I also just realised there's a smaller spring on the ground. Wondering if it fell out with out me noticing when I took the cover off.

Ali SC3

iTrader: (10)

yeah I think the same thing happened to me, forgot exactly but 2 sounds right, I can take my cover off later today and have a peek around haven't looked in there in quite a while.

Halon

iTrader: (6)

im going to have my buddy make up 2 more of those adapters with his remaining material, if anyone wants one.

Side note, CBF just posted up this pic on FB, hmmmm lol.

LoveSCs

iTrader: (2)

LMAO that's hilarious. Same exact piece you just made.

Hey I will take one of those pieces if they haven't been claimed yet. I doubt that I will have any issues with my JB welded piece, but would be nice to have that in my back pocket if my piece comes loose PM me your paypal and I will give you some $

Thanks,

Keith

Ali SC3

iTrader: (10)

yeah I know how you feel, its like all these places read our threads here and mass produce what we come up with... It took me like a week of scratching my head while staring at that transmission... several sketches... before I came up with the idea for getting it to 32", now everyone has a version of it... haha

Halon

iTrader: (6)

Lol, all good. If people want to pay $200+ for an out the door solution, so be it, and there's definitely a need and market for that.

But if people want to pay $60 for a DIY homemade version like this, well then that's what this is all about right here

Halon

iTrader: (6)

Pics of the Collins flywheel and my SB clutch I'll be running.

Halon

iTrader: (6)

Somebody please help!

So I took the top inspection cover off awhile back. I'm just about ready to install this trans, however I noticed there is the ball and long spring in that spot where they are supposed to be. But I also found this smaller and shorter spring sitting on the ground next to the trans. Wondering if there were 2 springs in there, and this one just fell out and I didn't notice it come out.

estomax

iTrader: (2)

Did you weigh the flywheel by Chance?

Halon

iTrader: (6)

FUnny thing, I did weight the flywheel. But of course I didn't write it down and so now I forgot lol. But if I remember right I think it was like 12-13lbs.

DriftOner

Did you pull out any of the really short 14mm bolts around the case of the transmission? The little springs go inside those holes. There shouldn't be little springs under the inspection plate.

Edit: Make sure you're not missing any of the detent ***** that go under the springs also.

Halon

iTrader: (6)

Talked to Fenning, thinks it probably came out of one of the sensors I chopped apart. So I think I'm OK.

And I've been making progress, but much slower than I had hoped. But progress is progress, and I'm just aiming for next year at this point. Here's where I'm at.

- Stock pilot bushing removed. Learned a new life hack in the method, removed it with 4 wet napkins and a punch in about 10 minutes! Lol. Then new Collins one installed in it's place.

- Flywheel mounted (M10 x 1.25 x 40mm ARP's). Torqued and Loctited.

- Clutch mounted. Torqued and Loctited.

- Shifter arrangement finalized. Made some spacers to replace the stack of washers. Shifter ends up 31 5/8" back from the block.

- Attempted to install the transmission, but it's just so heavy. It was getting late so I just decided to call it a night and will try again tonight.