something never been done to the headlights
#46
I'm really looking forward to this man . You are in the process of making something great and I hope that this works out as you expect because this would look bad***!! If this doesn't work out, maybe you can look into that other design posted earlier many members would buy them in my mind without a doubt. Anyways great progress, looking forward to more updates on this.
#47
Lexus Champion
Thread Starter
I'm really looking forward to this man . You are in the process of making something great and I hope that this works out as you expect because this would look bad***!! If this doesn't work out, maybe you can look into that other design posted earlier many members would buy them in my mind without a doubt. Anyways great progress, looking forward to more updates on this.
#48
Pole Position
iTrader: (1)
Join Date: May 2014
Location: Orlando, Florida
Posts: 243
Likes: 0
Received 0 Likes
on
0 Posts
i miscalculated it lol. i really didn't measure anything, i just went with it and wanted it to look good. so now just have to shrink it and simplify the inside of it because i'm wasting plastic on the inside. they charged me $11, the last one was $1.93 lol. they charge 10 cents by the gram
#49
Lexus Champion
Thread Starter
here's how much i had to adjust the size lol. the left is the old one, right is the new one, also removed a lot of detail on the inside that was wasting plastic and lots of rafts were inside pointlessly. i had a flat piece sticking out and now i just blended it into the body itself so less plastic used and less rafts and more rigid.
more measurements this time, not taking any chances, this R&D stuff is getting expensive lol
more measurements this time, not taking any chances, this R&D stuff is getting expensive lol
#50
#53
Lexus Champion
Thread Starter
well the 3D printed stuff is for the headlights, the tail lights i have something else in mind and it could be done the same way to the 95 tails as well. stay tuned, *****s about to go down lol. submitting the print again tonight. getting paid tomorrow so i'll be buying more supplies
#54
Lexus Champion
Thread Starter
do you guys care about if i upload the work files on here? is anyone interested in working side by side on their own version? i can upload OBJ, maya MB, maya ASCII, and FBX, and figure out other file types if you need them. let me know if anyone is interested and you guys can join along and build something similar or completely different. or learn along the way.
#55
Lexus Champion
Thread Starter
new print is done and it's almost perfect! just need to move it back, move it down a bit and maybe angle it, i'll do one angled and one straight and see how they look. the clips in the back are absolutely perfect fit, will make the tabs stick out further and less pronounced because it's really hard to take the housing back out lol, i actually broke one of the clips cz i had to press that hard to get it out (ABS doesn't bend very much, just cracks eventually)
ignore the rafting inside the light, still has to be cleaned up
as you can see, sticks out way too far lol
perfect fit on the clips, the whole housing sits incredibly snug
ignore the rafting inside the light, still has to be cleaned up
as you can see, sticks out way too far lol
perfect fit on the clips, the whole housing sits incredibly snug
#56
Lexus Champion
Thread Starter
so close!!! thought the lamp would fit without being tilted or resized but it looks like it won't, can't move the face back any further because it gets really stubby looking and i'm running out of room on the inside of the model. so i'm gonna tilt it back a little to match the line of the lens.
also, modeled and 3D printed the katakana font Toyota emblems! gonna sand and paint them tmr and stick em on the car! a repaint wuold be nice first but whatever.
this is almost perfect, just a couple more degrees of rotation needed
looks great from the front!
and the emblem!
also, modeled and 3D printed the katakana font Toyota emblems! gonna sand and paint them tmr and stick em on the car! a repaint wuold be nice first but whatever.
this is almost perfect, just a couple more degrees of rotation needed
looks great from the front!
and the emblem!
#58
Lexus Champion
Thread Starter
that's a good idea, i'll form it to the lens then, or at least attempt to.
#60
Lexus Champion
Thread Starter
yes i did actually! today i did it, painted the letters white with a paint marker and then clear coated. sorry for the splotches of primer, car really needs a paint job, but i'll probably do it after winter, what's the point of beating a new paint with salt.
temp plate while i was waiting for a replacement plate cz i lost my front one
i was thinking of putting the logo on the hood in the front instead of the bumper, haven't done it yet, what do you think? and also the new plate came in lol and the last pic was before i put it on. needs wash as well. i don't remember the last time i rinsed her down. probably do it when i raise it for the winter.
EDIT: those holes still need to be covered up, but i got something pretty hilarious for at least a few of them lol.
temp plate while i was waiting for a replacement plate cz i lost my front one
i was thinking of putting the logo on the hood in the front instead of the bumper, haven't done it yet, what do you think? and also the new plate came in lol and the last pic was before i put it on. needs wash as well. i don't remember the last time i rinsed her down. probably do it when i raise it for the winter.
EDIT: those holes still need to be covered up, but i got something pretty hilarious for at least a few of them lol.