It's been a while AKA (Sleeper2jz)
Sad times haha
02-12-15, 10:50 AM
#48
Intermediate
Thread Starter
Same here. I went with the gs430 magnaflow unit since it has better flow once the cat gets removed.
02-12-15, 11:07 AM
#49
For that pipe I have the magnaflow unit for the gs430. Just waiting on the flex I ordered to remove the cat. Should be on by next week since I don't weld ss and have to take it to a shop out here to do so.
Same here. I went with the gs430 magnaflow unit since it has better flow once the cat gets removed.
Same here. I went with the gs430 magnaflow unit since it has better flow once the cat gets removed.
02-12-15, 11:24 AM
#50
Also, I want to temporarily run my 2" diameter ss system from the CAT section back, is that an ok size? The Topspeed section I have is 2.25" (60mm) and I need to buy some back boxes to match.
Last edited by RichS11; 02-12-15 at 11:42 AM.
02-12-15, 03:57 PM
#51
Intermediate
Thread Starter
Ahh that's good to know. How come you went with flex over a straight pipe for the CAT?
Because engine mounts eventually go bad And would rather the y pipe have some flex than break.
Also, I want to temporarily run my 2" diameter ss system from the CAT section back, is that an ok size? The Topspeed section I have is 2.25" (60mm) and I need to buy some back boxes to match.
Because engine mounts eventually go bad And would rather the y pipe have some flex than break.
Also, I want to temporarily run my 2" diameter ss system from the CAT section back, is that an ok size? The Topspeed section I have is 2.25" (60mm) and I need to buy some back boxes to match.
02-13-15, 10:51 PM
#56
Intermediate
Thread Starter
[QU OTE=RichS11;8911643]Not going to weld the flex section on?[/QUOTE]
yes I am but pipe is meant for SC. going to use the Flex section 2 extend It Because it's to short
yes I am but pipe is meant for SC. going to use the Flex section 2 extend It Because it's to short
02-14-15, 02:15 AM
#57
Ahhh so the flex is going on the cat to extend it? I read a review saying that the section I've purchased is too small and needs extending for the 430. I am having the cat cut out and then having either a longer section of pipe or flex welded in so that it fits the 430.
Thanks for posting these pics as it's really helpful!
Thanks for posting these pics as it's really helpful!
02-14-15, 02:28 AM
#58
yes I am but pipe is meant for SC. going to use the Flex section 2 extend It Because it's to short[/QUOTE]
yes there was actually s DIY thread about a member using the SC430 y pipe from Megan I think and had to extend the 3rd muffler a little. everything else bolted right up
yes there was actually s DIY thread about a member using the SC430 y pipe from Megan I think and had to extend the 3rd muffler a little. everything else bolted right up
02-14-15, 03:08 AM
#59
Yeah I was under the impression I ordered a part for the GS430 but they are actually for the SC. Is there an option for me to cut out the muffler and go with extending it that way, or is hollowing it out the only route? I have a guy here who is an awesome welder, just haven't got the part in front of me to see for myself.
Sorry to ask lots of questions on your build up, but we both seem to be aiming our builds into very similar directions.
Sorry to ask lots of questions on your build up, but we both seem to be aiming our builds into very similar directions.
