92 SC400 cleaning it up geewwddd
#61
Lexus Champion
Thread Starter
it's def not past fixing, my first guess would be timing belt but there's no point in spending a third of the worth of the car just to get it running and who knows maybe that won't even work. my buddy said he'd charge me 80 an hour and the timing belt kit (idler pulley, PS pump and a few other things) is like 200 bucks off of ebay. i looked into the work and it says anywhere from 6 to 8 hours and that's over 400 bucks.
i would do the work myself but i just don't have time. i got school every single day and work at night every other day. sorry guys but i'm just gonna pass on this, i love this car so much and i was just sitting in it holding the steering wheel for like a half hour lol. i'll get another SC some other time for sure, i love this freaking car but it's just not the time for me. i'll still lurk on here just no more build for me.
i would do the work myself but i just don't have time. i got school every single day and work at night every other day. sorry guys but i'm just gonna pass on this, i love this car so much and i was just sitting in it holding the steering wheel for like a half hour lol. i'll get another SC some other time for sure, i love this freaking car but it's just not the time for me. i'll still lurk on here just no more build for me.
#63
Lexus Champion
Thread Starter
yea def parting it, gonna stick it in a storage place cz first month is a buck! try to get it parted out in a month. then it's going into scrap. friend has a huge saw that he loves cutting **** up with. unless someone will buy the shell
#64
Lexus Champion
iTrader: (10)
I went with the brakes this time. Today is a sad day though. Started the car to go to school and 10 seconds into running once i put it into drive it felt like it dropped a cylinder and started running really rough, so i turned it off, turned it back on, same thing.
Checked both coils, ran smoother on the passenger side one. So started taking it apart and the last plug all the way by the firewall had oil on it. So i got a bad spark plug gasket... Gonna take it out and clean it up once i get back from school, i think i had too much oil in the engine. It was 3/4 to full on the dip stick, didn't think it would be a problem because i had that much on the xB usually.
If that doesn't fix it, valve cover gaskets and spark gaskets and plugs. will get changed and then we'll see from there on.
Checked both coils, ran smoother on the passenger side one. So started taking it apart and the last plug all the way by the firewall had oil on it. So i got a bad spark plug gasket... Gonna take it out and clean it up once i get back from school, i think i had too much oil in the engine. It was 3/4 to full on the dip stick, didn't think it would be a problem because i had that much on the xB usually.
If that doesn't fix it, valve cover gaskets and spark gaskets and plugs. will get changed and then we'll see from there on.
sounds like you just lost a coilpack if you smell unburnt fuel, happens all the time and I read here you were checking out the coilpacks and one runs smoother? likely you already found the problem. If you want to send it over here Ill take it and change the coilpack for you, it takes like 10 minutes
the rotors are a little trickier but I would change those out as well, no reason to destroy the car. I haven't seen anyone destroy a 92 1uz without a ton of NOS or a very large badly tuned supercharger, the 1992 is arguably the strongest version of the 1uz motor.
Last edited by Ali SC3; 08-14-14 at 12:33 PM.
#65
Lexus Champion
Thread Starter
ok so a couple of my friends got me to take a second look at the car. i think the problem is the ignition coil. specifically the passenger side one which is weird cz its usually the driver side one cz its so close to the engine.
here's what they look like
it's the thing right at the bottom left, little box with 4 screws and 3 wires attached to it
not my bay btw, phones dead so couldn't get the pictures onto the comp right now.
so i unplugged the driver side one and the car wouldn't turn over or start, which is pretty good indication that the passenger one doesn't work, and they seem to be a common problem. the problem is though, one of the screws on the passenger side one is stuck and i can't get the passenger one off to unplug and check if the other side works.
i'm leaving for the weekend tomorrow and when i come back i'll go to the junk yard and grab some ignition coils from a 400 they have there with a smashed front end. there's still hope!!!! i feel really stupid and bad for just giving up on it like that. my bad guys.
gonna get it running and the mods will continue, starting with the new DBA rotors!
here's what they look like
it's the thing right at the bottom left, little box with 4 screws and 3 wires attached to it
not my bay btw, phones dead so couldn't get the pictures onto the comp right now.
so i unplugged the driver side one and the car wouldn't turn over or start, which is pretty good indication that the passenger one doesn't work, and they seem to be a common problem. the problem is though, one of the screws on the passenger side one is stuck and i can't get the passenger one off to unplug and check if the other side works.
i'm leaving for the weekend tomorrow and when i come back i'll go to the junk yard and grab some ignition coils from a 400 they have there with a smashed front end. there's still hope!!!! i feel really stupid and bad for just giving up on it like that. my bad guys.
gonna get it running and the mods will continue, starting with the new DBA rotors!
#67
Lexus Champion
Thread Starter
I'm considering buying a for sale 92 Sc4 but things like this scare me. How can I inspect and evaluate the condition of a 92 Sc4 and determine it's state of engine-related maintenance and also to gather some foresight into future knickknack or serious repairs? Anyone?
#68
Lexus Champion
Thread Starter
she RUNS! Scindy's back on the road and better than ever!
it was the driver ignition coil, changed it but ran into some trouble. the plug on the high tension cable just crumbled in my fingers so i electrical taped it up until i get a new plug or just leave it if i don't have any problems. also the screw holding the coil bracket to the engine, that broke while i was taking it off, the 2nd big screw on the right holding the bracket wasn't there at all. so i'll try to find one tmr to fill that spot because the bracket is just ziptied to another thing close by.
ALSO THE NEW ROTORS ARE IN! will put these on this weekend, and from there on i'll take a little break, need to save up for loans
once i got the money it's gonna be headers and exhaust, and manual swap! that's probably next summer. for now it's all cosmetic and cheap little things.
about the brake rotors, you can see the kangaroo paw pattern vanes in there, signature DBA stuff
it was the driver ignition coil, changed it but ran into some trouble. the plug on the high tension cable just crumbled in my fingers so i electrical taped it up until i get a new plug or just leave it if i don't have any problems. also the screw holding the coil bracket to the engine, that broke while i was taking it off, the 2nd big screw on the right holding the bracket wasn't there at all. so i'll try to find one tmr to fill that spot because the bracket is just ziptied to another thing close by.
ALSO THE NEW ROTORS ARE IN! will put these on this weekend, and from there on i'll take a little break, need to save up for loans
once i got the money it's gonna be headers and exhaust, and manual swap! that's probably next summer. for now it's all cosmetic and cheap little things.
about the brake rotors, you can see the kangaroo paw pattern vanes in there, signature DBA stuff
#69
Lexus Champion
Thread Starter
more troubles
got it figured out though.
installed the rotors today, was gonna go for a test drive, put the brakes down and bam, to the floor...
so checked all the brakes for leaks and brake fluid and what do you know. the passenger caliper was gushing with brake fluid. took the wheel off and a crack around the entire bleeder valve was pouring brake fluid out. FREAK OUT!!! then start calling every parts store in the area and finally found one half an hour away that had a caliper for sale, so took my dad's car and went and picked it up. so i was late to work because i was installing the new brake and it started pouring while i was putting the wheels back on. while the brake was leaking it lost a lot of brake fluid, just above minimum, so i drove to autozone and got some more fluid and asked the guys to pump the brakes for me while i bled the new caliper cz it was squishy beyond belief. well that's today and hopefully the last bad thing with the car. at least i got a new caliper lol.
car brakes awesome now! the bite on these rotors is amazing! it braked so hard my front bumper hit the ground, but didn't lock up! brakes finally feel great, but i gotta paint this new caliper cz it's got all the packaging and a crooked "Supra" emblem on it
got it figured out though.
installed the rotors today, was gonna go for a test drive, put the brakes down and bam, to the floor...
so checked all the brakes for leaks and brake fluid and what do you know. the passenger caliper was gushing with brake fluid. took the wheel off and a crack around the entire bleeder valve was pouring brake fluid out. FREAK OUT!!! then start calling every parts store in the area and finally found one half an hour away that had a caliper for sale, so took my dad's car and went and picked it up. so i was late to work because i was installing the new brake and it started pouring while i was putting the wheels back on. while the brake was leaking it lost a lot of brake fluid, just above minimum, so i drove to autozone and got some more fluid and asked the guys to pump the brakes for me while i bled the new caliper cz it was squishy beyond belief. well that's today and hopefully the last bad thing with the car. at least i got a new caliper lol.
car brakes awesome now! the bite on these rotors is amazing! it braked so hard my front bumper hit the ground, but didn't lock up! brakes finally feel great, but i gotta paint this new caliper cz it's got all the packaging and a crooked "Supra" emblem on it
#70
Moderator
iTrader: (71)
So glad you didn't write her off yet! thanks, and while some times we get frustrated with our "girls" don't give up...she's loyal! lol Great work with the brake calipers...could you pm me more info on the DBA brakes? I don't want to clutter you thread w/ questions? thx
steve
steve
#71
Lexus Champion
Thread Starter
So glad you didn't write her off yet! thanks, and while some times we get frustrated with our "girls" don't give up...she's loyal! lol Great work with the brake calipers...could you pm me more info on the DBA brakes? I don't want to clutter you thread w/ questions? thx
steve
steve
getting the old rotors resurfaced at oreillys tmr, 15 bucks a pop not bad, and new front and rear brake pads, maybe just front for now
#73
Lexus Champion
Thread Starter
yea lol, after this will be all cosmetics and cheap ricer stuff lol. i got a little more body work to do than yours. was sanding the front bumper a little, realized it's been repainted, really badly. paint is chipping and there's gray primer underneath, which isn't factory at all. oh well everything will be repainted or something idk. we'll see, i really hate the sandstone beige color though lol. i have no idea how you stand it, i just wanna plastidip mine already.
#74
Pole Position
iTrader: (18)
yea lol, after this will be all cosmetics and cheap ricer stuff lol. i got a little more body work to do than yours. was sanding the front bumper a little, realized it's been repainted, really badly. paint is chipping and there's gray primer underneath, which isn't factory at all. oh well everything will be repainted or something idk. we'll see, i really hate the sandstone beige color though lol. i have no idea how you stand it, i just wanna plastidip mine already.