Sc4 Build
#48
Rookie
Thread Starter
Join Date: Mar 2014
Location: Washington
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
Update... got some stuff done, got the engine bay all cleaned up and the EGR delete done.
Did my own little intake mod. I modified the factory tube and took the bog box thing off and patched the hole. Opened up the box some on the outside and made a heat shield to block all the hot engine bay air.
Did my own little intake mod. I modified the factory tube and took the bog box thing off and patched the hole. Opened up the box some on the outside and made a heat shield to block all the hot engine bay air.
#49
Rookie
Thread Starter
Join Date: Mar 2014
Location: Washington
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
Finally working on the car again!
finally got my spacer. got it and the clutch all put together.
and finally got the trans all in, had some fitting issues and had to open up the tunnel a little with a sledge.
and got the wiring for the speedo done, we'll see if it works....
The slave cylinder sits pretty close to the drivers cat so i wrapped it and the line in heat tape
finally got my spacer. got it and the clutch all put together.
and finally got the trans all in, had some fitting issues and had to open up the tunnel a little with a sledge.
and got the wiring for the speedo done, we'll see if it works....
The slave cylinder sits pretty close to the drivers cat so i wrapped it and the line in heat tape
#51
Rookie
Thread Starter
Join Date: Mar 2014
Location: Washington
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
Another update, went to the driveline place and dropped off my slip yoke and measurements, ended up having to order the Driftmotion 3 bolt to 4 bolt adaptor, will be here Friday.
#53
Moderator
iTrader: (71)
Nice build so far! Very clean install. Hey, not sure if I've missed it or not? If you haven't moved your harness in the wheel well, you should do so immediately. This will help save the harness from getting chewed up with that right height? Keep the mods coming, and I too can't wait to see the Z finish.
steve
steve
#54
Rookie
Thread Starter
Join Date: Mar 2014
Location: Washington
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
I'll have a update on it once i get my driveshaft. I used the abs speed sensor, I had my buddy wire it for me. I'm not as umm smart when it comes to wiring.
Nice build so far! Very clean install. Hey, not sure if I've missed it or not? If you haven't moved your harness in the wheel well, you should do so immediately. This will help save the harness from getting chewed up with that right height? Keep the mods coming, and I too can't wait to see the Z finish.
steve
steve
#55
Driver School Candidate
Join Date: Aug 2014
Location: NC
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Im very interested in knowing how the speedo signal works for you. If it works fine then im going to order one. Been looking for one for a couple weeks and im tired of using my gps as a speedo lol. Awesome looking car btw.
#56
Rookie
Thread Starter
Join Date: Mar 2014
Location: Washington
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
update: got the rest of it together, drives pretty good. but i ran into a issue... when i pulled all the lines for the hydro fan and capped them i didn't even think about the pulley so it seized on me today. so I'm hoping someone can give me some guidance here. Ive seen people switch to the ls400 pump and pulley and i have seen some people remove the guts of the sc400 pump and run that. so not sure which to do at this point, id like to not spend the money if i don't have to at this point since Ive already spent so much on the swap...
anyway, everybody likes pictures....
also I got some 95-96 tails last week
anyway, everybody likes pictures....
also I got some 95-96 tails last week
#57
Rookie
Thread Starter
Join Date: Mar 2014
Location: Washington
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
also, quick update on the Dakota digital box... I am getting a signal but I haven't figured out how to adjust it correctly yet so its kind of all over the place
#58
Driver School Candidate
Join Date: Aug 2014
Location: NC
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Sweet. Ive been trying to order one myself and figure it out. Need to wire one in myself and mess with it. Itll be sweet to see the speedo actually move. lol