Been 6 years....
#1
Pole Position
Thread Starter
Been 6 years....
Since I owned a Lexus. Was on the LS400 forum back in 2006-09. Now I'm in a SC400
My old LS400
My new car 1997 SC400. Picked it up about 2 weeks ago
First day when I got the sc
A week Later I decided to do a DIY Lip. Heres what I used:
Paver Edging from Home Depot and some screws
How it Turned out
How i mounted it
A few days ago I picked up some SC430 wheels and Got my coilovers and spacers in
cx racing coilovers 14k/10k
32mm Spacers
Decided to Install everything on Saturday
Spacers
Coilovers
Rolled the fenders
test fit the wheels
Also Put in a new door lock actuator which was a pain to install
THE OUTCOME... Also went for a wash
Then a quick Shoot
Overall Great car to own and I'm happy to be back in a Lexus! A few more mods coming in the near future. Enjoy
how it currently sits
My old LS400
My new car 1997 SC400. Picked it up about 2 weeks ago
First day when I got the sc
A week Later I decided to do a DIY Lip. Heres what I used:
Paver Edging from Home Depot and some screws
How it Turned out
How i mounted it
A few days ago I picked up some SC430 wheels and Got my coilovers and spacers in
cx racing coilovers 14k/10k
32mm Spacers
Decided to Install everything on Saturday
Spacers
Coilovers
Rolled the fenders
test fit the wheels
Also Put in a new door lock actuator which was a pain to install
THE OUTCOME... Also went for a wash
Then a quick Shoot
Overall Great car to own and I'm happy to be back in a Lexus! A few more mods coming in the near future. Enjoy
how it currently sits
Last edited by lp_yang; 05-04-15 at 10:27 PM.
#2
Lexus Champion
looking great, how much did that edging stuff cost? i wanna make my own lip and that stuff looks like it would be great as a base. can't wait to see more of this car, really clean.
Trending Topics
#9
Great stance, and the lip looks good too. I used something called the EZ Lip, its just stick on rubber except its made specifically for cars. Yours is a great alternative though (and $10 cheaper haha)
#11
Pole Position
Thread Starter
Thanks guys! Sway bar links are still stock. Should I change them?
I've seen the ez lip on sc before and was gonna try it but wanted something that looked more oem. Also the material used on the paver edging is plastic/abs so it feels oem
I've seen the ez lip on sc before and was gonna try it but wanted something that looked more oem. Also the material used on the paver edging is plastic/abs so it feels oem
#15
Pole Position
Thread Starter
Made a few changes in the past months
Relocated the wire harness
manzo axle back
Painted my taillights but cracked my lens so it was lens less for a few weeks
installed puddle lights
Went lower, 95-96 tail lights, wingless, and Hic roof spoiler
Riding on a buddies Miro wheels. 18x9.5 +34 with 32mm spacer so +2 offset
test fitting a carbonfiber splitter we had laying around
Installed and trimmed
Peeled off the green. This is how it currently sits
Relocated the wire harness
manzo axle back
Painted my taillights but cracked my lens so it was lens less for a few weeks
installed puddle lights
Went lower, 95-96 tail lights, wingless, and Hic roof spoiler
Riding on a buddies Miro wheels. 18x9.5 +34 with 32mm spacer so +2 offset
test fitting a carbonfiber splitter we had laying around
Installed and trimmed
Peeled off the green. This is how it currently sits