Project: COLOSUS
05-28-08, 06:39 AM
#1
Pole Position
Thread Starter
iTrader: (3)
Join Date: Mar 2007
Location: Edmonton area, Alberta
Posts: 309
Likes: 0
Received 5 Likes
on
5 Posts
Project: COLOSUS
Detials:
1991 Toyota Celsior
125,000kms
Black exterior
Tan Interior
19" Lowenhart rims
JIC Magic coilovers
Plans:
1. K&N filter & intake mod
2. Pioneer GPS
3. Billet Grill
4. JP rear cans
5. Battery Relocation to trunk
6. S&S headers
7. Custom 2.5" exhaust from headers to cans (cat, resonator & pre-mufflers all deleted)
8. Bullet Supercharger Kit
9. Nology Spark plug wires and NGK plugs
10. Water/Methanol injection kit
11. custom gauge mount (boost, egt, a/f)
12. strut braces (front and rear)
13. new tires... lol
.
.
.
urethane bushings, engine damper, brake master cylinder stopper, supra brake upgrade, stainless brake lines, etc.
1991 Toyota Celsior
125,000kms
Black exterior
Tan Interior
19" Lowenhart rims
JIC Magic coilovers
Plans:
1. K&N filter & intake mod
2. Pioneer GPS
3. Billet Grill
4. JP rear cans
5. Battery Relocation to trunk
6. S&S headers
7. Custom 2.5" exhaust from headers to cans (cat, resonator & pre-mufflers all deleted)
8. Bullet Supercharger Kit
9. Nology Spark plug wires and NGK plugs
10. Water/Methanol injection kit
11. custom gauge mount (boost, egt, a/f)
12. strut braces (front and rear)
13. new tires... lol
.
.
.
urethane bushings, engine damper, brake master cylinder stopper, supra brake upgrade, stainless brake lines, etc.
Last edited by Boyscout; 06-04-14 at 05:35 AM.
05-28-08, 06:41 AM
#2
Pole Position
Thread Starter
iTrader: (3)
Join Date: Mar 2007
Location: Edmonton area, Alberta
Posts: 309
Likes: 0
Received 5 Likes
on
5 Posts
Current Progress:
Im also thinking i will lower the front of the car 1/2" to make the wheel well gap a little less. I cant lower the car in the rear without rolling the fenders. (i only have 1/2" clearance in the rear because of the 275's...and i dont particularly want to roll the fenders)
Im also thinking i will lower the front of the car 1/2" to make the wheel well gap a little less. I cant lower the car in the rear without rolling the fenders. (i only have 1/2" clearance in the rear because of the 275's...and i dont particularly want to roll the fenders)
What kind of RWHP gains do you think you will see with the engine/exhaust upgrades?
Trending Topics
05-28-08, 12:43 PM
#12
Pole Position
Thread Starter
iTrader: (3)
Join Date: Mar 2007
Location: Edmonton area, Alberta
Posts: 309
Likes: 0
Received 5 Likes
on
5 Posts
1/2 an inch lower in the front wont make the car look retarded...it will just make the wheel well gap a bit smaller which will make the car look like it has a proper stance...right now it looks too high in the front end (i swapped the front coil springs and they are a bit taller then the ones that came out)
06-05-08, 08:36 AM
#14
Pole Position
Thread Starter
iTrader: (3)
Join Date: Mar 2007
Location: Edmonton area, Alberta
Posts: 309
Likes: 0
Received 5 Likes
on
5 Posts
reieved these parts yesterday:
- Battery Box
- Strut brace
I was thinking of removing the factory CD changer and trim from the right side of the trunk...the battery box should fit nicely. then i will just make some custom trim to make it look "finished". (the box is stainless...it just has a white protective film on it)
- Battery Box
- Strut brace
I was thinking of removing the factory CD changer and trim from the right side of the trunk...the battery box should fit nicely. then i will just make some custom trim to make it look "finished". (the box is stainless...it just has a white protective film on it)
Last edited by Boyscout; 09-12-11 at 01:38 PM.
