CatManD3W SC300 Ongoing Build...
02-13-14, 08:10 PM
Pole Position
Thread Starter
Join Date: May 2013
Location: Pittsburgh, PA
Posts: 2,207
Manifold has arrived..
More parts arriving over the next few weeks....
02-14-14, 08:34 PM
Pole Position
Thread Starter
Join Date: May 2013
Location: Pittsburgh, PA
Posts: 2,207
02-15-14, 05:19 AM
Super Moderator
Join Date: May 2009
Location: A Mile Ahead of You
Posts: 6,135
Nice
. Now go to work , clean up that 2jzgte harness
.
02-15-14, 10:57 AM
Moderator
Join Date: Sep 2008
Location: NC
Posts: 3,235
Great work bro, looking forward to the end...NICE! Now get back to work! haha
steve
02-15-14, 03:45 PM
Pole Position
Thread Starter
Join Date: May 2013
Location: Pittsburgh, PA
Posts: 2,207
Quote:
Originally Posted by
lilSCsteve
Great work bro, looking forward to the end...NICE! Now get back to work! haha
steve
Quote:
Originally Posted by
gerrb
Nice
. Now go to work , clean up that 2jzgte harness
.
Thanks...I got a lot of work ahead of me just picked up my engine stand and torque wrench
02-16-14, 08:32 AM
Pole Position
Thread Starter
Join Date: May 2013
Location: Pittsburgh, PA
Posts: 2,207
02-16-14, 04:18 PM
Pole Position
Thread Starter
Join Date: May 2013
Location: Pittsburgh, PA
Posts: 2,207
Got the intake side removed today....Along with wiring harness
I ended up labeling every clip and connector when i removed it...making it much easier to identify each plug when i start on harness build.
Power steering and A/C compressor removed..
Fuel injectors are removed from lower intake runner...
Lower runners removed....I am very pleased so far the engine is really clean..
02-16-14, 04:47 PM
1JZ Single SC400
Join Date: Jan 2009
Location: Alabama, Roll Tide!
Posts: 8,518
Likes: 0
Progress is coming along quite nicely. Keep up the good work.
02-16-14, 05:59 PM
Pole Position
Thread Starter
Join Date: May 2013
Location: Pittsburgh, PA
Posts: 2,207
Quote:
Originally Posted by
1JZPWRD
Progress is coming along quite nicely. Keep up the good work.
Thanks...Tomorrow I am going to dive deep into the harness
02-18-14, 08:12 AM
Pole Position
Thread Starter
Join Date: May 2013
Location: Pittsburgh, PA
Posts: 2,207
Harness work started...
I am about half way finished with the harness at this point..
Last edited by CatManD3W; 02-18-14 at 08:15 AM .
02-18-14, 10:52 AM
Driver School Candidate
Join Date: Jan 2014
Location: Oregon
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
02-18-14, 02:21 PM
Driver
Join Date: Apr 2012
Location: Tx
Posts: 146
Likes: 0
Received 0 Likes
on
0 Posts
must go faster must go faster
02-18-14, 03:00 PM
Pole Position
Thread Starter
Join Date: May 2013
Location: Pittsburgh, PA
Posts: 2,207
Quote:
Originally Posted by
wth98sc
must go faster must go faster
Slow and steady man...dont get your hopes up no reason for me to rush it
02-19-14, 04:03 PM
Pole Position
Thread Starter
Join Date: May 2013
Location: Pittsburgh, PA
Posts: 2,207
Got crank pulley off and serpentine belt tensioner....
I was worrired I wouldnt be able to get the crank pulley bolt out but I put the stock auto flywheel back on and wedged a big screwdriver in it to prevent the crank for spinning...
I used a breaker bar with the 4ft handle from my jack to make a cheater bar...worked well
02-19-14, 07:55 PM
Driver
Join Date: Apr 2012
Location: Tx
Posts: 146
Likes: 0
Received 0 Likes
on
0 Posts
seems to be the best method :P