My ´97 SC400
#212
HY!
On the front, i installed back the Supra springs and on rear, lowered i today the spring dish 6mm to lower the car approx 10mm
but before, i tested with my Girlfriend an my Girly how much i must lowering
looks good ~1cm lower
and front ~1cm lower
today the new position 6mm lower
95% ready only on the front right side is the car 10-13mm higher as on the driver side, but i have no idea why. i will also lowering the spring dish a little to have near the same high
greets
Tom
On the front, i installed back the Supra springs and on rear, lowered i today the spring dish 6mm to lower the car approx 10mm
but before, i tested with my Girlfriend an my Girly how much i must lowering
looks good ~1cm lower
and front ~1cm lower
today the new position 6mm lower
95% ready only on the front right side is the car 10-13mm higher as on the driver side, but i have no idea why. i will also lowering the spring dish a little to have near the same high
greets
Tom
Last edited by Boergy; 06-02-12 at 10:52 AM.
#218
Hey mate, just wanted to say your SC looks delicious.
I have the same paint code as you, and am inspired to get mine looking in the same pristine condition as yours.
However mines only a 91 with a 97 front bumper. But will be getting the side skirts and bumper this year sometime.
I have the same paint code as you, and am inspired to get mine looking in the same pristine condition as yours.
However mines only a 91 with a 97 front bumper. But will be getting the side skirts and bumper this year sometime.
#219
HY!
@pieisgude..yes..i have a little dent in the front fender
@LatidudeNZ... thanks!
I hope, ihave next week time to install the Supra TT AT oil cooler and the big Audi A8 power steering cooler. On the 09.09 we will start a day on a little raceway in Austria to drift on a wet street but i will also have finished my exhaust...many to do, and no time, family and my home are first.
here some old vids
@pieisgude..yes..i have a little dent in the front fender
@LatidudeNZ... thanks!
I hope, ihave next week time to install the Supra TT AT oil cooler and the big Audi A8 power steering cooler. On the 09.09 we will start a day on a little raceway in Austria to drift on a wet street but i will also have finished my exhaust...many to do, and no time, family and my home are first.
here some old vids
#220
Hello
Today, i installed the A8 steering cooler in my SC, fits good, looks original we changed the oil complete from the power steering, it was brown, not red more.
The front bumper remove is not easy! many many srews and clips, headlight remove....
all from the bumper and headlights!
old cooler removed
new one with little modifications installed
Heater Fan Cooler
new place for the Supra TT AT Cooler
my friend Robert is measurement for the cooler holder plate
the power steering cooler is done, tomorrow i hope, i can install the AT Cooler
2 pictures from last week
greets
Tom
Today, i installed the A8 steering cooler in my SC, fits good, looks original we changed the oil complete from the power steering, it was brown, not red more.
The front bumper remove is not easy! many many srews and clips, headlight remove....
all from the bumper and headlights!
old cooler removed
new one with little modifications installed
Heater Fan Cooler
new place for the Supra TT AT Cooler
my friend Robert is measurement for the cooler holder plate
the power steering cooler is done, tomorrow i hope, i can install the AT Cooler
2 pictures from last week
greets
Tom
#222
HY!
The Coolers are fitted perfect, without any contact to other parts
very interesting is, the turn signal lamp have 3 contacts, but the cable only 2. is this in any country original?
last days i modified a IS200/300 catalytic to a 1 cell race catalytic
The new stainless steel pipe have 70mm (2 3/4") and the flange fits perfect to the original flange from the rear part of the exhaust.
3rd catalytic
original welded pipe
new mid-pipe
tomorrow i will check to fit the IS cat. on the pipe, i hope, i have enough clearance to the headshield on the car.
more tomorrow
greets
Tom
The Coolers are fitted perfect, without any contact to other parts
very interesting is, the turn signal lamp have 3 contacts, but the cable only 2. is this in any country original?
last days i modified a IS200/300 catalytic to a 1 cell race catalytic
The new stainless steel pipe have 70mm (2 3/4") and the flange fits perfect to the original flange from the rear part of the exhaust.
3rd catalytic
original welded pipe
new mid-pipe
tomorrow i will check to fit the IS cat. on the pipe, i hope, i have enough clearance to the headshield on the car.
more tomorrow
greets
Tom
#223
Hy!
the exhaust workshop is finished
70mm Pipe and 3rd Catalytic dummy filled, welded and the heatshield fixed
and here the soundcheck after a short turn
http://www.youtube.com/watch?v=uCOma...ature=youtu.be
greets
Tom
the exhaust workshop is finished
70mm Pipe and 3rd Catalytic dummy filled, welded and the heatshield fixed
and here the soundcheck after a short turn
http://www.youtube.com/watch?v=uCOma...ature=youtu.be
greets
Tom