CarPro HydrO2... buy it!
#166
HydrO2 Lite is a less concentrated product that is pre-mixed, ready to use... so no work on your end when it comes to mixing the product or anything like that.
HydrO2 Lite can be applied in the same fashion as HydrO2... ie spray onto wet surface, then immediate rinse. It can also be applied like a quick detailer... ie mist lightly onto the surface, spread, and buff away with a microfiber towel.
Due to the less concentrated formula, the durability is not as good as the highly concentrated formula that can only be applied wet.
I have been told that this product will be an inexpensive alternative to HydrO2 for those who are seeking a rtu product for quick touch ups/added protection on a regular basis.
-Zach
#167
First... you should've diluted as the directions state. The chemicals which state proper dilution ratios are not just a suggestion, they are a requirement.
Water beading is caused by high surface tension. Protection products vary in the level of surface tension, and therefore the characteristics of the beading you see after applying a particular product. If, for instance, you use a very hydrophobic property, and then cover it with a product that doesn't display the same type of beading, you may assume the first product simply doesn't bead well or is worn away (which you had mentioned).
In your case, I would imagine the shampoo that you used was your issue, or perhaps the weak dilution of HydrO2 concentrate. For future maintenance, I would recommend a traditional shampoo without any waxes in it (and read the directions for proper dilution of the shampoo! A heavily mixed shampoo can and will strip waxes and sealants from the paint, so that may have also been an issue).
I see... haven't ever experienced that. I never considered Rain X to be a durable product and would reapply it at least every other month when I used it to maintain hydrophobic properties. Since then, I have found products that I prefer greatly due to either ease of use, durability, or both.
Water beading is caused by high surface tension. Protection products vary in the level of surface tension, and therefore the characteristics of the beading you see after applying a particular product. If, for instance, you use a very hydrophobic property, and then cover it with a product that doesn't display the same type of beading, you may assume the first product simply doesn't bead well or is worn away (which you had mentioned).
In your case, I would imagine the shampoo that you used was your issue, or perhaps the weak dilution of HydrO2 concentrate. For future maintenance, I would recommend a traditional shampoo without any waxes in it (and read the directions for proper dilution of the shampoo! A heavily mixed shampoo can and will strip waxes and sealants from the paint, so that may have also been an issue).
I see... haven't ever experienced that. I never considered Rain X to be a durable product and would reapply it at least every other month when I used it to maintain hydrophobic properties. Since then, I have found products that I prefer greatly due to either ease of use, durability, or both.
Last edited by qboy3388; 05-13-15 at 02:44 AM.
#168
Moderator
iTrader: (20)
It does not seem to be available here in the US yet... I have some for testing and will post a new thread with my findings after I have some more time to play with it.
HydrO2 Lite is a less concentrated product that is pre-mixed, ready to use... so no work on your end when it comes to mixing the product or anything like that.
HydrO2 Lite can be applied in the same fashion as HydrO2... ie spray onto wet surface, then immediate rinse. It can also be applied like a quick detailer... ie mist lightly onto the surface, spread, and buff away with a microfiber towel.
Due to the less concentrated formula, the durability is not as good as the highly concentrated formula that can only be applied wet.
I have been told that this product will be an inexpensive alternative to HydrO2 for those who are seeking a rtu product for quick touch ups/added protection on a regular basis.
-Zach
HydrO2 Lite is a less concentrated product that is pre-mixed, ready to use... so no work on your end when it comes to mixing the product or anything like that.
HydrO2 Lite can be applied in the same fashion as HydrO2... ie spray onto wet surface, then immediate rinse. It can also be applied like a quick detailer... ie mist lightly onto the surface, spread, and buff away with a microfiber towel.
Due to the less concentrated formula, the durability is not as good as the highly concentrated formula that can only be applied wet.
I have been told that this product will be an inexpensive alternative to HydrO2 for those who are seeking a rtu product for quick touch ups/added protection on a regular basis.
-Zach
#170
Lexus Test Driver
I hope the price reflects the lower concentration, otherwise it isn't worth it. Similar to buying a full gallon of coolant for $1.00 more than half the amount in the 50:50 concentration.
#171
Thank you very much for your help! I guess I will return meguiars ultimate wash and wax i just bought. Could you recommend me a good shampoo? I'm looking at meguiar's gold class car wash. I don't really need anything pro/expensive. I just need some shampoo that would clean my car nicely and not effect hydro2.
I plan on posting an introductory review on the other detailing forums around the web and will copy it into here as well.
You know where to find me
-Zach
#173
A question about these products. So I have a clean wet car, but if I look at the surface there are areas that have water and areas where there is no water.
So if I spray the product on, some will land on dry paint and some will be very diluted when the product hits the water on the paint. Of course the amount of water still on the car will vary greatly. So I'm left wondering how this product can work if some of the mist lands on dry paint and some lands on larger water spots/pools?
It kinda makes sense with a product like Reload where you wipe it off after application, but I'm having a hard time wrapping my head around HydroO2 and how it works? As I ended up applying too much product trying to ensure good coverage.
I read this thread after applying the product as per the simple instructions on the bottle and made a mess of my new car. Mixed it properly but used a whole bottle on the car and appplied as per the bottles instructions using a high pressure washer to remove the product. The end result was lots of streaking and the product stuck onto the windows
I was able to get it off the windows by using a very plush Griots Micro Fiber Towel (cheaper decent towels did nothing), and a ton of elbow grease. But didn't have the time or energy to get it off the rest of the car.
Any idea of which Shampoo to use to get the residual product off as quick as possible as I was hoping to CQuartz it before winter?
So if I spray the product on, some will land on dry paint and some will be very diluted when the product hits the water on the paint. Of course the amount of water still on the car will vary greatly. So I'm left wondering how this product can work if some of the mist lands on dry paint and some lands on larger water spots/pools?
It kinda makes sense with a product like Reload where you wipe it off after application, but I'm having a hard time wrapping my head around HydroO2 and how it works? As I ended up applying too much product trying to ensure good coverage.
I read this thread after applying the product as per the simple instructions on the bottle and made a mess of my new car. Mixed it properly but used a whole bottle on the car and appplied as per the bottles instructions using a high pressure washer to remove the product. The end result was lots of streaking and the product stuck onto the windows
I was able to get it off the windows by using a very plush Griots Micro Fiber Towel (cheaper decent towels did nothing), and a ton of elbow grease. But didn't have the time or energy to get it off the rest of the car.
Any idea of which Shampoo to use to get the residual product off as quick as possible as I was hoping to CQuartz it before winter?
#174
A question about these products. So I have a clean wet car, but if I look at the surface there are areas that have water and areas where there is no water.
So if I spray the product on, some will land on dry paint and some will be very diluted when the product hits the water on the paint. Of course the amount of water still on the car will vary greatly. So I'm left wondering how this product can work if some of the mist lands on dry paint and some lands on larger water spots/pools?
It kinda makes sense with a product like Reload where you wipe it off after application, but I'm having a hard time wrapping my head around HydroO2 and how it works? As I ended up applying too much product trying to ensure good coverage.
I read this thread after applying the product as per the simple instructions on the bottle and made a mess of my new car. Mixed it properly but used a whole bottle on the car and appplied as per the bottles instructions using a high pressure washer to remove the product. The end result was lots of streaking and the product stuck onto the windows
I was able to get it off the windows by using a very plush Griots Micro Fiber Towel (cheaper decent towels did nothing), and a ton of elbow grease. But didn't have the time or energy to get it off the rest of the car.
Any idea of which Shampoo to use to get the residual product off as quick as possible as I was hoping to CQuartz it before winter?
So if I spray the product on, some will land on dry paint and some will be very diluted when the product hits the water on the paint. Of course the amount of water still on the car will vary greatly. So I'm left wondering how this product can work if some of the mist lands on dry paint and some lands on larger water spots/pools?
It kinda makes sense with a product like Reload where you wipe it off after application, but I'm having a hard time wrapping my head around HydroO2 and how it works? As I ended up applying too much product trying to ensure good coverage.
I read this thread after applying the product as per the simple instructions on the bottle and made a mess of my new car. Mixed it properly but used a whole bottle on the car and appplied as per the bottles instructions using a high pressure washer to remove the product. The end result was lots of streaking and the product stuck onto the windows
I was able to get it off the windows by using a very plush Griots Micro Fiber Towel (cheaper decent towels did nothing), and a ton of elbow grease. But didn't have the time or energy to get it off the rest of the car.
Any idea of which Shampoo to use to get the residual product off as quick as possible as I was hoping to CQuartz it before winter?
You must be very aware of where the mist is landing, and where the rinse water is going. Thoroughly rinse any area that may have come in contact with HydrO2 to avoid streaking.
CarPro HydrO2 Application Tips - Zach McGovern
Reload is a different product that is applied like a quick detailer... mist onto dry paint, then spread and buff off immediately with a high quality microfiber towel. You can't go wrong with either HydrO2 or Reload for quick and easy protection... the benefit to HydrO2 is that you can apply it to the entire car in just a few minutes without any additional tools/towels during the wash process. I personally use HydrO2 most on my wheels, and prefer Reload on my paint.
Depending on how severe your streaking is, washing may or may not remove the residue. Try a heavy mixture of whatever shampoo you've got laying around. You may need to pre-soak the area with a paint safe All-Purpose cleaner like P21S Total Auto Wash for even more cleaning. The streaks will eventually wear away.
#175
Ordered last Monday & came in on Wednesday. Didn't get a chance to try it until this past Saturday on my neglected Infiniti EX35 (last time I washed this car must have been around last Christmas). Count me as a true believer! Awesome product & easy to use to go with. Definitely recommend anyone who's still skeptic about this product.
#176
Ordered last Monday & came in on Wednesday. Didn't get a chance to try it until this past Saturday on my neglected Infiniti EX35 (last time I washed this car must have been around last Christmas). Count me as a true believer! Awesome product & easy to use to go with. Definitely recommend anyone who's still skeptic about this product.
#178
Zach, I just ordered the Hydro02 directly from Carpro. As I read the directions, it calls for a 1:4 mixing ratio. Has the mixing ration changed from 1:3 to 1:4? What ratio are we supposed to use?