CA 01+ Tail light, NA-T Piping, Body Molding (Chrome),
#1
01+ Tail light, NA-T Piping, Body Molding (Chrome),
Here's the direct link to UPS and USPS' websites
https://wwwapps.ups.com/ctc/request?...WT.svl=PNRO_L1
http://www.usps.com/tools/calculatep...lculatepostage
Reasonable offers are welcomed.
SOLD !!! 01+ Complete OEM Toyota Tail Light (Inner and Outer)
Thanks to the clowns at DTM Autobody, one of the tab is cracked. Otherwise, these would be in perfect condition. The actual stud still sits firmly in the original socket. These tail lights are from a 01+ car, so they will never fade like the 98-99 ones.
I will separate inners and outers if i have buyers for both.
Damage on the passenger side outer tail light:
SOLD
2.5" NA-T Intercooler Piping (Cut-to-fit)
This will fit your na-t setup with ge manifold. Made out of 100% aluminum, the MAF bung is welded on the cold side for blow-through. All piping ends are beaded. Comes with t-bolts and 3-ply couplers. This is a textbook 3 coupler per side build:
1x 2.5" on the turbine
2x on the intercooler (2.5" to 3")
1x on the throttle body (2.5" to 2.75")
and 2x 2.5" couplers in between.
25 lbs. $400 OBO
98-05 IS300 GS300 Alternator
A little rusted, but otherwise in good condition. I would swap out the pulley for another one. 80k miles.
20 lbs. $50
Rear Body Molding Assembly 75730-30252
This goes between the rear side windows and the door, right underneath where it says "garage club"
There's a few dents, as well as a 1 or 2 broken clips (again, thanks to the clowns at DTM Autbobody).
3lbs. +1 Oversized Package.
$40 for both
BRAND NEW DDM Tuning 9006 3000K HID Kits
Lifetime warranty on ballast and bulb.
$40 or $50 shipped!
Thanks for looking!
https://wwwapps.ups.com/ctc/request?...WT.svl=PNRO_L1
http://www.usps.com/tools/calculatep...lculatepostage
Reasonable offers are welcomed.
SOLD !!! 01+ Complete OEM Toyota Tail Light (Inner and Outer)
Thanks to the clowns at DTM Autobody, one of the tab is cracked. Otherwise, these would be in perfect condition. The actual stud still sits firmly in the original socket. These tail lights are from a 01+ car, so they will never fade like the 98-99 ones.
I will separate inners and outers if i have buyers for both.
Damage on the passenger side outer tail light:
SOLD
2.5" NA-T Intercooler Piping (Cut-to-fit)
This will fit your na-t setup with ge manifold. Made out of 100% aluminum, the MAF bung is welded on the cold side for blow-through. All piping ends are beaded. Comes with t-bolts and 3-ply couplers. This is a textbook 3 coupler per side build:
1x 2.5" on the turbine
2x on the intercooler (2.5" to 3")
1x on the throttle body (2.5" to 2.75")
and 2x 2.5" couplers in between.
25 lbs. $400 OBO
98-05 IS300 GS300 Alternator
A little rusted, but otherwise in good condition. I would swap out the pulley for another one. 80k miles.
20 lbs. $50
Rear Body Molding Assembly 75730-30252
This goes between the rear side windows and the door, right underneath where it says "garage club"
There's a few dents, as well as a 1 or 2 broken clips (again, thanks to the clowns at DTM Autbobody).
3lbs. +1 Oversized Package.
$40 for both
BRAND NEW DDM Tuning 9006 3000K HID Kits
Lifetime warranty on ballast and bulb.
$40 or $50 shipped!
Thanks for looking!
Last edited by ElitistK; 02-05-11 at 08:32 AM.
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
chanhichan
2Gen GS430 / 400/ 300 Classifieds (98-05)
5
10-19-05 09:19 PM