FS: Apexi WS Catback
10-15-08, 10:25 PM
#1
Lexus Test Driver
Thread Starter
iTrader: (1)
Join Date: Jul 2006
Location: Chicago
Posts: 847
Likes: 0
Received 0 Likes
on
0 Posts
FS: Apexi WS Catback
Selling a Apexi WS2 catback. used for about a year. selling it for 400 dollars. still pretty shiny. just small scratch on the bottom of the tip. because my garage is a bit steep so when my car gets out its scrapes it a bit.
10-16-08, 05:20 PM
#5
Lexus Test Driver
Thread Starter
iTrader: (1)
Join Date: Jul 2006
Location: Chicago
Posts: 847
Likes: 0
Received 0 Likes
on
0 Posts
mike the scratches are not bad i will post up pictures tonight. you can get these bad boys on no problem. muffler shop has to create new hangers for you. have you heard how the exhaust sounds on youtube?
10-16-08, 11:45 PM
#7
Lexus Test Driver
Thread Starter
iTrader: (1)
Join Date: Jul 2006
Location: Chicago
Posts: 847
Likes: 0
Received 0 Likes
on
0 Posts
hey mike heres the link. http://www.youtube.com/watch?v=xxHd9gGQiw4 here is one on an is300 sounds similar http://www.youtube.com/watch?v=NA9yX2z6_bE
im located in the west side of the city down by archer and california
im located in the west side of the city down by archer and california
Trending Topics
10-17-08, 06:32 AM
#9
sounds pretty good. is that how the exhaust sits in the first pic? can you take a pic of the top and the flange for me please. Our cars are very different if you didnt know I have one mid pipe that runs the car and the exhaust is a U tube that goes into both mufflers. So from the mid pipe it goes into a T then from there its a U shape to exit through the mufflers. The 2gen GS has dual pipes. This is the only thing we need to see if I can fit it under the body and from what i can recall from being under the car I think I have to have them run down the center of the car and not flare out as they do in the pic up top. If they sit together and its just how you have them sitting then we should be fine. I just would need a custom pipe from there to join to the headers.
10-17-08, 07:51 AM
#12
Lexus Test Driver
Thread Starter
iTrader: (1)
Join Date: Jul 2006
Location: Chicago
Posts: 847
Likes: 0
Received 0 Likes
on
0 Posts
this how your exhaust would look. see the hangers are and the te pipes. my friend has a camry and he had bought some catback that was made for a is250/350, which the bends are correct but the flange is different. 
10-17-08, 09:12 AM
#13
sorry this would require too much custom work and I am better to move forward with the custom exhaust at that point.
Thanks for your help and getting me the info.
Neurocity!!! (Matt) this has your name all over it...Listen to how good that sounds on your car.
back to the drawing board for me. I just wish I could life the car up after hours and slap something on. Tanabe is nice but too quiet for what I want and I dont like the Greddy or HKS set ups.
Thanks for your help and getting me the info.
Neurocity!!! (Matt) this has your name all over it...Listen to how good that sounds on your car.
back to the drawing board for me. I just wish I could life the car up after hours and slap something on. Tanabe is nice but too quiet for what I want and I dont like the Greddy or HKS set ups.
